Dynamite PASSPORT Ultra Duo Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Ładowarka Dynamite PASSPORT Ultra Duo. Dynamite PASSPORT Ultra Duo 2 stron. 100w lcd ac/dc multi-chemistry battery charger
Również dla Dynamite PASSPORT Ultra Duo: Instrukcja instalacji (10 strony)

Dynamite PASSPORT Ultra Duo Instrukcja obsługi
InstructIon Manual | BedIenungsanleItung | Manuel d'utIlIsatIon | Manuale dI IstruzIonI
• Never attempt to charge a battery pack containing different types of batteries.
NOTICE
• Never allow children under 14 years of age to charge battery packs.
All instructions, warranties and other collateral documents are subject to change
• Never charge batteries in extremely hot or cold places or place in direct sunlight.
at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit
• Never charge a battery if the cable has been pinched or shorted.
horizonhobby.com and click on the support tab for this product.
• Never connect the charger if the power cable has been pinched or shorted.
• Never connect the charger to an automobile 12V battery while the vehicle
Meaning of Special Language
is running.
The following terms are used throughout the product literature to indicate various
• Never attempt to dismantle the charger or use a damaged charger.
levels of potential harm when operating this product:
• Never attach your charger to both an AC and a DC power source at the same time.
NOTICE: Procedures, which if not properly followed, create a possibility of physical
• Never connect the input jack (DC input) to AC power.
• Always use only rechargeable batteries designed for use with this type of charger.
property damage AND a little or no possibility of injury.
• Always inspect the battery before charging.
CAUTION: Procedures, which if not properly followed, create the probability of
• Always keep the battery away from any material that could be affected by heat.
physical property damage AND a possibility of serious injury.
• Always monitor the charging area and have a fire extinguisher available at all times.
WARNING: Procedures, which if not properly followed, create the probability of
• Always end the charging process if the battery becomes hot to the touch or starts
property damage, collateral damage, and serious injury OR create a high probability
to change form (swell) during the charge process.
of superficial injury.
• Always connect the charge cable to the charger first, then connect the battery to
avoid short circuit between the charge leads. Reverse the sequence when
WARNING: Read the ENTIRE instruction manual to become familiar with the
disconnecting.
features of the product before operating. Failure to operate the product
• Always connect the positive red leads (+) and negative black leads (–) correctly.
correctly can result in damage to the product, personal property and cause
• Always disconnect the battery after charging, and let the charger cool between
charges.
serious injury.
• Always charge in a well-ventilated area.
This is a sophisticated hobby product. It must be operated with caution and common
• Always terminate all processes and contact Horizon Hobby if the product
sense and requires some basic mechanical ability. Failure to operate this Product
malfunctions.
in a safe and responsible manner could result in injury or damage to the product or
WARNING: Never leave charger unattended, exceed maximum charge rate,
other property. This product is not intended for use by children without direct adult
charge with non-approved batteries or charge batteries in the wrong mode.
supervision. Do not attempt disassembly, use with incompatible components or
Failure to comply may result in excessive heat, fire and serious injury.
augment product in any way without the approval of Horizon Hobby, Inc. This manual
contains instructions for safety, operation and maintenance. It is essential to read and
CAUTION: Always ensure the battery you are charging meets the
follow all the instructions and warnings in the manual, prior to assembly, setup or use,
specifications of this charger and that the charger settings are correct. Not
in order to operate correctly and avoid damage or serious injury.
doing so can result in excessive heat and other related product malfunctions,
Age Recommendation: Not for children under 14 years. This is not a toy.
which can lead to user injury or property damage. Please contact Horizon
SAfETy PRECAUTIONS ANd WARNINGS
Hobby or an authorized retailer with compatibility questions.
WARNING: Failure to exercise caution while using this product and comply
with the following warnings could result in product malfunction, electrical
issues, excessive heat, FIRE, and ultimately injury and property damage.
• Never leave the power supply, charger and battery unattended during use.
• Never attempt to charge dead, damaged or wet battery packs.
over-temperature protection
Included Items
• Storage and Fast Charge modes
JST_XH Balance adapter (2)
• User battery data, store and load up to 10 battery profiles
• (2) 2x16 backlit, blue LCD
Banana plug to EC3
battery connector (2)
• Insulated, color coded, banana jack, power output terminals (Red = Positive (+),
AC power cord (one region-US, EU, AU or UK)
Black = Common or Negative (–))
• Internal cooling fans with grill covers
OPTIONAL ACCESSORIES
• Operating temperature range of 0°C to +50°C
DYN4012 - DC Power Cord
• Meets IP33CW, IK07 environmental specs
DYN5031 - Insulated Charge Adapter, Banana to EC3 Device
• Rugged industrial plastic case
DYN5032 - Balancing Adapter Board
SPECIfICATIONS
DYN5033 - Temperature Sensor: DYN4103, DYN4300
Minimum computer requirements for use of included software: Microsoft
®
AC Input Voltage 100–240V AC (50/60Hz)
Windows XP
®
, Windows 7
®
or Windows Vista
®
operating system, Compact disk (CD)
DC Input Voltage 11–18V DC
reader capable of reading a mini-CD and USB 2.0 port.
Charge Current 0.10 to 10.0A per channel (in 0.1A increments/200W
fEATURES
maximum per channel/400W Total)
• Two charging ports to charge two batteries at once. Batteries can be different
capacities and cell counts
Discharge Current 0.10 to 5.0A per channel (in 0.1A increments/25W
• 1A USB charge port compatible with iPhone
®
, iPod
®
or similar products
maximum per channel/50W Total)
• 100–240V AC (50/60Hz) or 11–18V DC input voltage
Operating temperature 0°C to +50°C
• Li-Ion/Li-Po/Li-Fe battery cell count of 1 to 6 series cells
Balance Current Drain 300mA per cell
• Ni-Cd/Ni-MH battery cell count of 1 to 15 cells
Trickle Charge Current 50 to 200mA
• Pb battery voltage of 2 to 20V
• Built-in 50W discharger
Charging Mode Peak (Ni-Cd/Ni-MH), CC/CV (Li-Po/Li-Ion/Li-Fe/Pb)
• Built-in balance circuit
• Short-circuit, over-current, reverse polarity, low input voltage and
3
LI-fE BALANCE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
To select values other than the existing parameters:
locate the PROGRAM SELECT LiFe BATT screen. Press the Jog dial to go into this
• Press the Jog dial so the charge current value (A) flashes
menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the LiFe BALANCE screen and set charging param-
• Press the Jog dial to save the value and the voltage value (B) flashes
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
dependent on the number of cells in series. For example, with Li-Fe batteries these
series (C))
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
• Press the Jog dial to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another program
LiFe BALANCE
such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
5.5A
19.8V(6S)
To start charging, press and hold the Jog dial for 3 seconds.
A
B
C
4
LI-fE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
To select values other than the existing parameters:
locate the PROGRAM SELECT LiFe BATT screen. Press the Jog dial to go into this
• Press the Jog dial so the charge current value (A) flashes
menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the LiFe CHARGE screen and set charging parameters.
• Press the Jog dial to save the value and the voltage value (B) flashes
The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
series (C))
dependent on the number of cells in series. For example, with Li-Fe batteries these
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
• Press the Jog dial to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another program
LiFe CHARGE
such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
4.6A
19.8V(6S)
To start charging, press and hold the Jog dial for 3 seconds.
CAUTION: If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
A
B
C
charge process as batteries can cause fire, collateral damage and injuries.
5
LI-fE fAST CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
LiFe FAST CHG
locate the PROGRAM SELECT LiFe BATT screen. Press the Jog dial to go into this
menu.
0.1A
19.8V(6S)
Rotate the Jog dial to go to the LiFe FAST CHG screen and set charging param-
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
dependent on the number of cells in series. For example, with Li-Fe batteries these
A
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
To select values other than the existing parameters:
Near the end of a standard charging cycle, the charger switches from Constant Cur-
• Press the Jog dial so the charge current value (A) flashes
rent (CC) mode to Constant Voltage (CV) mode to slowly "top off" the current in the
battery as close as possible to the maximum capacity.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
• Press the Jog dial to save the value and the voltage value (B) flashes
In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
time; however, the final capacity of the battery will be less than what you would get
series (C))
using the standard charge method.
• Press the Jog dial to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another program
such as CHARGE, BALANCE, STORAGE or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
6
LI-fE STORAGE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
To select values other than the existing parameters:
locate the PROGRAM SELECT LiFe BATT screen. Press the Jog dial to go into this
• Press the Jog dial so the charge current value (A) flashes
menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the LiFe STORAGE screen and set charging param-
• Press the Jog dial to save the value and the voltage value (B) flashes
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
dependent on the number of cells in series. For example, with Li-Fe batteries these
series (C))
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
• Press the Jog dial to save the voltage value
If you don't plan on using your battery for a long time, it is best to charge (or
If no parameters are flashing, you can rotate the Jog dial to select another program
discharge) the battery to its optimal storage voltage and capacity.
such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
LiFe STORAGE
2.5A
19.8V(6S)
A
B
C
Not to scale.
Not all wiring shown.
Not all connectors shown.
GETTING STARTEd
When Using an External AC Power Source:
1. Connect the AC power cord to the charger AC power input port.
CAUTION: Never connect the AC and DC input cords to an active power
2. Connect the AC power cord to the AC power source.
source at the same time. This will void the warranty, cause product
3. Power ON the charger with the power switch.
damage and possibly injure the user.
4. When the charger is powered ON, a message will appear on the LCD screen.
When Using an External dC Power Source:
CAUTION: Always power ON the charger before connecting a battery, or
1. Connect the DC power cord to the charger DC power input port.
damage to the charger and the battery can result.
2. Connect the DC alligator clips to the DC power source.
1. Connect the charger to the power source.
3. Power ON the charger with the power switch.
4. When the charger is powered ON, a message will appear on the LCD screen.
2. Power ON the charger.
3. Make program selections in the charger for battery charging.
NOTICE: Always connect cable polarities correctly.
4. Connect the charger adapters to the charger.
NOTICE: Always consult 12V battery collateral materials or Horizon Hobby before
5. C onnect the battery to the charger adapters (connect main charging
using with sources other than a standard AC wall outlet.
connectors before connecting cell-balancing connectors, where used).
6. Start battery charging.
A. Power Output Red (+)
B. Power Output Black (–)
C. Balance Circuit Adapter
K.
Board Connector
d. Temperature Probe Connection
E. Mode/Stop Key
J.
f. USB Communications Port
G. 1A USB Charge Port
H. Jog Dial
I. LCD Screen
J. AC Power Input Port
K. Power Switch
L. DC Power Input/
APP Connectors
L.
7
LI-fE dISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
To select values other than the existing parameters:
locate the PROGRAM SELECT LiFe BATT screen. Press the Jog dial to go into this
• Press the Jog dial so the discharge current value (A) flashes
menu.
• Rotate the Jog dial to INCREASE OR DECREASE the discharge current value
Rotate the Jog dial to go to the LiFe DISCHARGE screen and set discharging pa-
• Press the Jog dial to save the value and the voltage value (B) flashes
rameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
(B) is dependent on the number of cells in series. For example, with Li-Fe batteries
series (C))
these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
• Press the Jog dial to save the voltage value
A battery's capacity can be verified by discharging it to its minimum voltage level
If no parameters are flashing, you can rotate the Jog dial to select another program
and measuring the current as the battery is discharged.
such as CHARGE, BALANCE, FAST CHG or STORAGE.
To start discharging, press and hold the Jog dial for 3 seconds.
LiFe DISCHARGE
2.0A
19.8V(6S)
A
B
C
8
LI-IO BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
locate the PROGRAM SELECT LiIo BATT screen. Press the Jog dial to select LiIo.
LI 3S 2.0A 12.59V
Rotate the Jog dial to go to one of the control screens (BALANCE, CHARGE, FAST
A
BAL 022:43 01082
CHG, STORAGE or DISCHARGE) to do what your battery needs.
Correctly connect your lithium battery to the charger (charging connector first and
balancing connector second). Press the Jog dial and adjust the charging param-
C. Charging rate is 2.0A (2000mAh)
eters as needed. Press and hold the Jog dial (approximately 3 seconds) until the
d. Voltage being applied to the battery is currently 12.59V
screen changes to start the battery check/charge sequence.
E. Present charge level of the battery is 1082mAh
A
f. Time elapsed since the charge process started is 22:43
When the charge cycle starts, the
R: 3SER
S:3SER
charger compares the battery to
During charging, the Jog dial can be rotated counterclockwise to show several
charger settings. The screen will show
CONFIRM
(ENTER)
parameter messages on the LCD screen, including: End Voltage, Input Power Volt-
the battery and your settings
age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and
information. If the information after R: (charger) and S: (settings) (A) does not match,
Capacity Cutoff.
press the Mode key and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the Jog dial to confirm.
Rotate the Jog dial clockwise to show the charge voltages for each cell. Press the
Jog dial at any time to return to the Charge Monitor screen. The charger signals
After confirmation, charging starts and information will show on the LCD screen
when the charging (or discharging) process is complete (if Buzzer is set to ON).
(information may vary).
B
C
9
LI-IO BALANCE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
To select values other than the existing parameters:
locate the PROGRAM SELECT LiIo BATT screen. Press the Jog dial to go into this
• Press the Jog dial so the charge current value (A) flashes
menu.
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
Rotate the Jog dial to go to the LiIo BALANCE screen and set charging parameters.
• Press the Jog dial to save the value and the voltage value (B) flashes
The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
dependent on the number of cells in series. For example, with Li-Io batteries these
series (C))
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
• Press the Jog dial to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another program
LiIo BALANCE
such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
5.5A
21.6V(6S)
A
B
C
LiFe BALANCE
2.0A
LiFe CHARGE
2.0A
LiFe FAST CHG
PROGRAM SELECT
PROGRAMMING qUICK GUIdE
LiFe BATT
2.0A
Press the Mode key (G) to get to the 9 main menus from any submenu screen.
LiFe STORAGE
Press the Jog dial (H) to get to the submenus for adjusting operating parameters, to save value changes or to start chosen battery charging actions.
2.0A
Rotate the Jog dial (H) to change between submenu screens or to change screen values.
LiFe DISCHARGE
2.0A
LiFe BALANCE
2.0A
LiIo BALANCE
LITHIUM BATTERIES (Li-fe)
LiFe CHARGE
2.0A
2.0A
LiIo CHARGE
PROGRAM SELECT
LiFe FAST CHG
2.0A
LiFe BATT
2.0A
PROGRAM SELECT
LiIo FAST CHG
LiIo BATT
2.0A
LiFe STORAGE
2.0A
LiIo STORAGE
LiFe DISCHARGE
2.0A
PROGRAM SELECT
2.0A
LiIo DISCHARGE
LiFe BATT
PROGRAM SELECT
2.0A
LiFe BATT
LiIo BALANCE
2.0A
LiPo BALANCE
LiIo CHARGE
2.0A
LITHIUM BATTERIES (Li-Po)
2.0A
LiPo CHARGE
PROGRAM SELECT
LiIo FAST CHG
2.0A
LiIo BATT
2.0A
LiPo FAST CHG
PROGRAM SELECT
LiPo BATT
2.0A
LiIo STORAGE
2.0A
LiPo STORAGE
LiIo DISCHARGE
2.0A
PROGRAM SELECT
2.0A
LiPo DISCHARGE
LiIo BATT
PROGRAM SELECT
2.0A
LiIo BATT
LiPo BALANCE
2.0A
[BATT MEMORY 1]
LiPo CHARGE
LiFe BALANCE
NiMH CHARGE
2.0A
2.0A
19.8V(6S)
CURRENT
BATT TYPE
LiFe BALANCE
Ni-MH BATTERIES
NiMH CHARGE
LiPo
LiPo FAST CHG
PROGRAM SELECT
LiFe CHARGE
NiMH Auto CHARGE
2.0A
19.8V(6S)
CURRENT
LiPo BATT
2.0A
2.0A
19.8V(6S)
CURRENT
BATT VOLTS
LiFe BALANCE
LiFe CHARGE
NiMH CHARGE
NiMH Auto CHARGE
LiPo STORAGE
LiFe FAST CHG
NiMH DISCHARGE
PROGRAM SELECT
2.0A
2.0A
19.8V(6S)
19.8V(6S)
PROGRAM SELECT
CURRENT
CURRENT
2.0A
2.0A
19.8V(6S)
NiMH BATT
0.1A
LiFe BATT
CHARGE CURRENT
PROGRAM SELECT
LiFe FAST CHG
LiFe CHARGE
PROGRAM SELECT
NiMH DISCHARGE
NiMH Auto CHARGE
LiPo DISCHARGE
NiMH RE-PEAK
LiFe BATT
LiFe STORAGE
2.0A
2.0A
19.8V(6S)
19.8V(6S)
NiMH BATT
0.1A
CURRENT
PROGRAM SELECT
2.0A
2.0A
19.8V(6S)
PROGRAM SELECT
DSCH CURRENT
LiPo BATT
LiFe STORAGE
LiFe FAST CHG
PROGRAM SELECT
PROGRAM SELECT
NiMH RE-PEAK
NiMH DISCHARGE
PROGRAM SELECT
BATT MEMORY
LiPo BATT
[BATT MEMORY 1]
NiMH CYCLE
LiFe BATT
2.0A
2.0A
LiFe DISCHARGE
19.8V(6S)
19.8V(6S)
NiMH BATT
0.1A
2.0A
19.8V(6S)
DCHG>CHG
DSCH VOLTAGE
LiFe DISCHARGE
LiFe STORAGE
NiMH RE-PEAK
NiMH CYCLE
BATT TYPE
2.0A
2.0A
19.8V(6S)
19.8V(6S)
DCHG>CHG
LiIo BALANCE
NiCd CHARGE
LiPo
TVC=YOUR RISK!
2.0A
21.6V(6S)
CURRENT
LiFe DISCHARGE
NiMH CYCLE
LiIo BALANCE
NiCd CHARGE
2.0A
19.8V(6S)
BATT VOLTS
DCHG>CHG
LiIo CHARGE
NiCd Auto CHARGE
2.0A
21.6V(6S)
CURRENT
Ni-Cd BATTERIES
TEMPERATURE
2.0A
21.6V(6S)
CURRENT
LiIo BALANCE
LiIo CHARGE
NiCd CHARGE
CUT-OFF
NiCd Auto CHARGE
CHARGE CURRENT
PROGRAM SELECT
NiCd DISCHARGE
PROGRAM SELECT
LiIo FAST CHG
2.0A
2.0A
21.6V(6S)
21.6V(6S)
CURRENT
CURRENT
SAVE PROGRAM
LiIo BATT
2.0A
21.6V(6S)
NiCd BATT
0.1A
PROGRAM SELECT
LiIo FAST CHG
LiIo CHARGE
PROGRAM SELECT
NiCd DISCHARGE
NiCd Auto CHARGE
PROGRAM SELECT
DSCH CURRENT
LiIo BATT
LiIo STORAGE
2.0A
2.0A
21.6V(6S)
21.6V(6S)
NiCd BATT
NiCd RE-PEAK
CURRENT
0.1A
BATT MEMORY
2.0A
21.6V(6S)
PROGRAM SELECT
LiIo FAST CHG
LiIo STORAGE
PROGRAM SELECT
NiCd RE-PEAK
NiCd DISCHARGE
DSCH VOLTAGE
LiIo BATT
LiIo DISCHARGE
2.0A
2.0A
21.6V(6S)
21.6V(6S)
NiCd BATT
0.1A
NiCd CYCLE
DCHG>CHG
2.0A
21.6V(6S)
LiIo DISCHARGE
LiIo STORAGE
NiCd RE-PEAK
NiCd CYCLE
TVC=YOUR RISK!
2.0A
2.0A
21.6V(6S)
21.6V(6S)
DCHG>CHG
LiPo BALANCE
PROGRAM SELECT
Pb CHARGE
2.0A
22.2V(6S)
PROGRAM SELECT
BATT MEMORY
2.0A
PROGRAM SELECT
NiCd CYCLE
LiIo DISCHARGE
LiPo BALANCE
TEMPERATURE
Pb CHARGE
BATT MEMORY
2.0A
21.6V(6S)
Pb BATT
DCHG>CHG
2.0A
LiPo CHARGE
22.2V(6S)
Pb BATTERIES
CUT-OFF
Pb DISCHARGE
2.0A
PROGRAM SELECT
2.0A
22.2V(6S)
2.0A
Pb BATT
LiPo CHARGE
LiPo BALANCE
SAVE PROGRAM
Pb DISCHARGE
Pb CHARGE
PROGRAM SELECT
2.0A
2.0A
LiPo FAST CHG
22.2V(6S)
22.2V(6S)
2.0A
2.0A
PROGRAM SELECT
Rest Time
2.0A
22.2V(6S)
LiPo BATT
Pb BATT
CHG>DCHG
PROGRAM SELECT
LiPo FAST CHG
LiPo CHARGE
Pb DISCHARGE
Rest Time
A.
LiPo BATT
B.
H.
C.
I. D.
LiPo STORAGE
2.0A
2.0A
E.
F.
22.2V(6S)
G.
22.2V(6S)
2.0A
CHG>DCHG
SAFETY TIMER
2.0A
22.2V(6S)
ON
LiPo STORAGE
LiPo FAST CHG
PROGRAM SELECT
SAFETY TIMER
Rest Time
LiPo BATT
LiPo DISCHARGE
2.0A
2.0A
22.2V(6S)
22.2V(6S)
CHG>DCHG
Capacity Cut-Off
ON
2.0A
22.2V(6S)
ON
LiPo DISCHARGE
LiPo STORAGE
10
Capacity Cut-Off
SAFETY TIMER
2.0A
2.0A
22.2V(6S)
22.2V(6S)
[BATT MEMORY 1]
LI-IO CHARGING
ON
ON
Key Beep
ENTER SET ->
Buzzer
LiPo DISCHARGE
[BATT MEMORY 1]
Key Beep
Capacity Cut-Off
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
2.0A
22.2V(6S)
PROGRAM SELECT
BATT TYPE
ENTER SET ->
ON
Buzzer
Input Power Low
locate the PROGRAM SELECT LiIo BATT screen. Press the Jog dial to go into this
LiPo
SYSTEM SET->
Cut-Off
menu.
[BATT MEMORY 1]
BATT TYPE
PROGRAM SELECT
Input Power Low
Key Beep
SYSTEM SET->
LiPo
BATT VOLTS
ENTER SET ->
Ext. Temp
Buzzer
Cut-Off
Rotate the Jog dial to go to the LiIo CHARGE screen and set charging parameters.
7.4V(2S)
Int. Temp
The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
BATT VOLTS
BATT TYPE
PROGRAM SELECT
Input Power Low
Ext. Temp
dependent on the number of cells in series. For example, with Li-Io batteries these
LiPo
CHARGE CURRENT
7.4V(2S)
SYSTEM SET->
LOAD FACTORY SET
Cut-Off
Int. Temp
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
2.2A
CHARGE CURRENT
BATT VOLTS
Ext. Temp
LOAD FACTORY SET
PROGRAM SELECT
DSCH CURRENT
7.4V(2S)
2.2A
VERSION
LiIo CHARGE
Int. Temp
BATT MEMORY
1.0A
PROGRAM SELECT
DSCH CURRENT
CHARGE CURRENT
VERSION
LOAD FACTORY SET
4.6A
21.6V(6S)
BATT MEMORY
DSCH VOLTAGE
2.2A
1.0A
0.00 0.00 0.00 V
3.0V/CELL
PROGRAM SELECT
0.00 0.00 0.00 V
DSCH VOLTAGE
DSCH CURRENT
PROGRAM SELECT
VERSION
0.00 0.00 0.00 V
BATT MEMORY
TVC=YOUR RISK!
3.0V/CELL
1.0A
LI BATT METER
0.00 0.00 0.00 V
MAIN 00.00V
PROGRAM SELECT
A
B
4.20V
H0.000V
DSCH VOLTAGE
TVC=YOUR RISK!
LI BATT METER
0.00 0.00 0.00 V
MAIN 00.00V
TEMPERATURE
4.20V
11
3.0V/CELL
H0.000V
0.00 0.00 0.00 V
PROGRAM SELECT
CUT-OFF
50C
LI-IO fAST CHARGING
TEMPERATURE
TVC=YOUR RISK!
LI BATT METER
MAIN 00.00V
SAVE PROGRAM
CUT-OFF
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
50C
4.20V
H0.000V
ENTER
locate the PROGRAM SELECT LiIo BATT screen. Press the Jog dial to go into this
TEMPERATURE
SAVE PROGRAM
menu.
CUT-OFF
ENTER
50C
Rotate the Jog dial to go to the LiIo FAST CHG screen and set charging param-
SAVE PROGRAM
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
ENTER
dependent on the number of cells in series. For example, with Li-Io batteries these
B
C
d
A. A Li-Io battery pack is balance
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
charging
Near the end of a standard charging cycle, the charger switches from Constant Cur-
B. Battery pack has 3 cells in
rent (CC) mode to Constant Voltage (CV) mode to slowly "top off" the current in the
series
battery as close as possible to the maximum capacity.
f
E
In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging
time; however, the final capacity of the battery will be less than what you would get
using the standard charge method.
12
LI-IO STORAGE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
locate the PROGRAM SELECT LiIo BATT screen. Press the Jog dial to go into this
menu.
Rotate the Jog dial to go to the LiIo STORAGE screen and set charging parameters.
CAUTION: The Li-Io program menus are to be used ONLY for the charging
The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
and discharging of Li-Io battery packs. The charging of other battery types
dependent on the number of cells in series. For example, with Li-Io batteries these
using these programs will result in damage to the battery or charger.
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
CAUTION: Using a charge rate that is not compatible with the battery
If you don't plan on using your battery for a long time, it is best to charge (or
capacities may result in damage or malfunction of the charger or
discharge) the battery to its optimal storage voltage and capacity.
batteries.
LiIo STORAGE
2.5A
21.6V(6S)
A
B
13
LI-IO dISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
locate the PROGRAM SELECT LiIo BATT screen. Press the Jog dial to go into this
menu.
Rotate the Jog dial to go to the LiIo DISCHARGE screen and set discharging param-
eters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage (B)
is dependent on the number of cells in series. For example, with Li-Io batteries these
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
A battery's capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.
LiIo DISCHARGE
2.0A
21.6V(6S)
A
B
LiFe STORAGE
2.0A
19.8V(6S)
LiFe DISCHARGE
2.0A
19.8V(6S)
LiFe BALANCE
LiIo BALANCE
2.0A
19.8V(6S)
NiMH CHARGE
2.0A
21.6V(6S)
19.8V(6S)
CURRENT
LiFe CHARGE
2.0A
LiIo CHARGE
2.0A
19.8V(6S)
NiMH Auto CHARGE
2.0A
21.6V(6S)
19.8V(6S)
CURRENT
LiFe FAST CHG
2.0A
PROGRAM SELECT
PROGRAM SELECT
PROGRAM SELECT
LiIo FAST CHG
PROGRAM SELECT
LiFe BATT
2.0A
19.8V(6S)
NiMH BATT
PROGRAM SELECT
LiIo BATT
NiMH DISCHARGE
2.0A
21.6V(6S)
NiCd BATT
19.8V(6S)
NiMH BATT
0.1A
LiFe STORAGE
CUT:1.0V
LiIo STORAGE
2.0A
19.8V(6S)
TABLE Of CONTENTS
NiMH RE-PEAK
2.0A
21.6V(6S)
1 SELF TEST AND PROGRAM SELECT SCREENS
19.8V(6S)
LiFe DISCHARGE
2
LiIo DISCHARGE
2.0A
19.8V(6S)
LI-fE
NiMH CYCLE
2.0A
21.6V(6S)
2 LI-FE BATTERIES
19.8V(6S)
DCHG>CHG
1
NiMH CHARGE
LiIo BALANCE
LiPo BALANCE
3 LI-FE BALANCE CHARGING
19.8V(6S)
CURRENT
2.0A
2.0A
21.6V(6S)
NiCd CHARGE
2.0A
22.2V(6S)
4 LI-FE CHARGING
PROGRAM SELECT
LITHIUM BATTERIES (Li-Ion)
21.6V(6S)
NiMH Auto CHARGE
CURRENT
LiIo CHARGE
2.0A
Pb BATT
5 LI-FE FAST CHARGING
LiPo CHARGE
19.8V(6S)
CURRENT
2.0A
2.0A
21.6V(6S)
6 LI-FE STORAGE CHARGING
NiCd Auto CHARGE
2.0A
22.2V(6S)
21.6V(6S)
PROGRAM SELECT
PROGRAM SELECT
CURRENT
NiMH DISCHARGE
LiIo FAST CHG
2.0A
PROGRAM SELECT
7 LI-FE DISCHARGE
PROGRAM SELECT
LiPo FAST CHG
LiFe BALANCE
19.8V(6S)
NiMH BATT
LiIo BATT
0.1A
NiMH CHARGE
2.0A
CUT:1.0V
21.6V(6S)
NiCd BATT
LI-IO
PROGRAM SELECT
LiPo BATT
NiCd DISCHARGE
2.0A
22.2V(6S)
2.0A
19.8V(6S)
CURRENT
2.0A
LiFe BALANCE
NiMH CHARGE
21.6V(6S)
NiCd BATT
NiMH RE-PEAK
0.1A
LiIo STORAGE
CUT: 1.0V
8 LI-IO BATTERIES
2.0A
19.8V(6S)
LiPo STORAGE
CURRENT
2.0A
LiFe CHARGE
19.8V(6S)
2.0A
NiMH Auto CHARGE
21.6V(6S)
2
9 LI-IO BALANCE CHARGING
NiCd RE-PEAK
2.0A
22.2V(6S)
LiFe CHARGE
2.0A
19.8V(6S)
NiMH Auto CHARGE
CURRENT
2.0A
10 LI-IO CHARGING
21.6V(6S)
NiMH CYCLE
LiIo DISCHARGE
2
2.0A
19.8V(6S)
CURRENT
2.0A
LiPo DISCHARGE
LiFe FAST CHG
19.8V(6S)
PROGRAM SELECT
DCHG>CHG
NiMH DISCHARGE
2.0A
21.6V(6S)
1
11 LI-IO FAST CHARGING
NiCd CYCLE
2.0A
22.2V(6S)
2.0A
LiFe FAST CHG
19.8V(6S)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A
CUT:1.0V
12 LI-IO STORAGE CHARGING
21.6V(6S)
DCHG>CHG
1
2.0A
19.8V(6S)
NiMH BATT
NiCd CHARGE
LiPo BALANCE
0.1A
CUT:1.0V
13 LI-IO DISCHARGE
LiFe STORAGE
NiMH RE-PEAK
[BATT MEMORY 1]
21.6V(6S)
CURRENT
2.0A
2.0A
22.2V(6S)
2
PROGRAM SELECT
LiFe STORAGE
2.0A
19.8V(6S)
Pb CHARGE
NiMH RE-PEAK
ENTER SET ->
LI-PO
Pb BATT
2.0A
22.2V(6S)
19.8V(6S)
2.0A
NiCd Auto CHARGE
LiPo CHARGE
2.0V (1P)
2
PROGRAM SELECT
14 LI-PO BATTERIES
LiFe DISCHARGE
NiMH CYCLE
BATT TYPE
PROGRAM SELECT
21.6V(6S)
CURRENT
2.0A
2.0A
22.2V(6S)
Pb BATT
SYSTEM SET->
2.0A
19.8V(6S)
Pb DISCHARGE
NiMH CYCLE
LiPo
DCHG>CHG
1
15 LI-PO BALANCE CHARGING
LiFe DISCHARGE
2.0A
22.2V(6S)
19.8V(6S)
PROGRAM SELECT
2.0A
NiCd DISCHARGE
LiPo FAST CHG
DCHG>CHG
2.0V (1P)
1
16 LI-PO CHARGING
PROGRAM SELECT
BATT VOLTS
LiIo BALANCE
21.6V(6S)
NiCd BATT
LiPo BATT
0.1A
2.0A
NiCd CHARGE
CUT: 1.0V
22.2V(6S)
17 LI-PO FAST CHARGING
7.4V(2S)
2.0A
LiIo BALANCE
21.6V(6S)
BATTERy MEMORy
Rest Time
NiCd CHARGE
CURRENT
2.0A
1
22.2V(6S)
NiCd RE-PEAK
LiPo STORAGE
2.0A
21.6V(6S)
CHG>DCHG
CHARGE CURRENT
CURRENT
10min
2.0A
SELf TEST ANd PROGRAM SELECT SCREENS
LiIo CHARGE
21.6V(6S)
2.0A
NiCd Auto CHARGE
22.2V(6S)
2
2.2A
LiIo CHARGE
2.0A
21.6V(6S)
SAFETY TIMER
CURRENT
NiCd Auto CHARGE
2.0A
When the charger is powered ON, there is a series of self tests and the screen will
22.2V(6S)
NiCd CYCLE
LiPo DISCHARGE
2.0A
21.6V(6S)
PROGRAM SELECT
ON
CURRENT
120min
2.0A
DSCH CURRENT
LiIo FAST CHG
21.6V(6S)
PROGRAM SELECT
DCHG>CHG
2.0A
NiCd DISCHARGE
22.2V(6S)
1
show the charger brand name and model number.
BATT MEMORY
1.0A
2.0A
LiIo FAST CHG
21.6V(6S)
PROGRAM SELECT
NiCd BATT
Capacity Cut-Off
NiCd DISCHARGE
0.1A
CUT: 1.0V
22.2V(6S)
2.0A
21.6V(6S)
NiCd BATT
ON
Pb CHARGE
0.1A
[BATT MEMORY 1]
5000mAh
CUT: 1.0V
DSCH VOLTAGE
LiIo STORAGE
NiCd RE-PEAK
22.2V(6S)
2.0A
2.0V (1P)
ENTER SET ->
3.0V/CELL
PROGRAM SELECT
2.0A
LiIo STORAGE
21.6V(6S)
NiCd RE-PEAK
2
Key Beep
ON
PROGRAM SELECT
Pb BATT
ENTER SET ->
2.0A
21.6V(6S)
Buzzer
Pb DISCHARGE
BATT TYPE
ON
2
PROGRAM SELECT
TVC=YOUR RISK!
LI BATT METER
LiIo DISCHARGE
NiCd CYCLE
22.2V(6S)
2.0A
LiPo
2.0V (1P)
4.20V
SYSTEM SET->
2.0A
2.0A
21.6V(6S)
PROGRAM SELECT
DCHG>CHG
1
2
LiIo DISCHARGE
Input Power Low
NiCd CYCLE
2.0A
21.6V(6S)
SYSTEM SET->
Cut-Off
DCHG>CHG
11.0V
1
LI-fE BATTERIES
BATT VOLTS
TEMPERATURE
Rest Time
2.0A
LiPo BALANCE
22.2V(6S)
CUT-OFF
Pb CHARGE
7.4V(2S)
50C
2.0A
CHG>DCHG
10min
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
Ext. Temp
0C
LiPo BALANCE
2.0A
22.2V(6S)
2.0A
Pb CHARGE
2.0V (1P)
PROGRAM SELECT
7.4V(2S)
locate the PROGRAM SELECT LiFe BATT screen. Press the Jog dial to select LiFe.
Int. Temp
CHARGE CURRENT
SAVE PROGRAM
32C
2.0A
22.2V(6S)
Pb BATT
SAFETY TIMER
2.0A
2.0V (1P)
2.0A
2.0A
PROGRAM SELECT
LiPo CHARGE
22.2V(6S)
Pb DISCHARGE
2.2A
ENTER
CUT:1.0V
ON
120min
Rotate the Jog dial to go to one of the control screens (BALANCE, CHARGE, FAST
Pb BATT
LOAD FACTORY SET
LiPo CHARGE
2.0A
22.2V(6S)
Pb DISCHARGE
2.0A
2.0V (1P)
2.2A
PROGRAM SELECT
CHG, STORAGE or DISCHARGE) to do what your battery needs.
DSCH CURRENT
ENTER
2.0A
22.2V(6S)
Capacity Cut-Off
2.0A
2.0V (1P)
CUT:1.0V
2.0A
LiPo FAST CHG
22.2V(6S)
BATT MEMORY
1.0A
2
ON
Rest Time
5000mAh
Correctly connect your lithium battery to the charger (charging connector first and
VERSION
2.0A
22.2V(6S)
LiPo FAST CHG
1.0A
CHG>DCHG
Rest Time
10min
balancing connector second). Press the Jog dial and adjust charging parameters
DSCH VOLTAGE
1.00
2.0A
22.2V(6S)
Key Beep
ON
CUT:1.0V
2
LiPo STORAGE
CHG>DCHG
10min
as needed. Press and hold the Jog dial (approximately 3 seconds) until the screen
3.0V/CELL
ENTER SET ->
1
Buzzer
SAFETY TIMER
ON
PROGRAM SELECT
2.0A
22.2V(6S)
changes to start the battery check/charge sequence.
LiPo STORAGE
0.00 0.00 0.00 V
ON
SAFETY TIMER
120min
3.0V/CELL
TVC=YOUR RISK!
LI BATT METER
2.0A
22.2V(6S)
PROGRAM SELECT
0.00 0.00 0.00 V
1
2
PROGRAM SELECT
Input Power Low
LiPo DISCHARGE
ON
120min
4.20V
SYSTEM SET->
Cut-Off
Capacity Cut-Off
11.0V
LI BATT METER
2.0A
2.0A
22.2V(6S)
LiPo DISCHARGE
MAIN 00.00V
R: 3SER
4.20V
ON
5000mAh
Capacity Cut-Off
TEMPERATURE
SySTEM SET
2.0A
22.2V(6S)
1
Ext. Temp
H0.000V
L0.000V
0C
ON
5000mAh
CONFIRM
2.0A
CUT-OFF
50C
[BATT MEMORY 1]
7.4V(2S)
Int. Temp
Key Beep
32C
ON
2.0A
[BATT MEMORY 1]
ENTER SET ->
Buzzer
ON
50C
SAVE PROGRAM
Key Beep
ON
information. If the information after R: (charger) and S: (settings) (A) does not match,
LOAD FACTORY SET
ENTER SET ->
Buzzer
ON
2.0A
2.0A
ENTER
press the Mode key and change the lithium battery charging parameters as
BATT TYPE
2.2A
PROGRAM SELECT
Input Power Low
ENTER
CUT: 1.0V
SYSTEM SET->
needed. If the R: information matches S:, press the Jog dial to confirm. After
BATT TYPE
LiPo
PROGRAM SELECT
Cut-Off
11.0V
ENTER
Input Power Low
VERSION
LiPo
SYSTEM SET->
confirmation, charging starts and information will show on the LCD screen
CUT: 1.0V
2.0A
Cut-Off
11.0V
BATT VOLTS
1.0A
Ext. Temp
1.00
0C
2
(information may vary).
7.4V(2S)
Int. Temp
32C
BATT VOLTS
Ext. Temp
0C
7.4V(2S)
CUT: 1.0V
2
0.00 0.00 0.00 V
Int. Temp
32C
CHARGE CURRENT
3.0V/CELL
LOAD FACTORY SET
1
0.00 0.00 0.00 V
PROGRAM SELECT
2.2A
ENTER
CHARGE CURRENT
LOAD FACTORY SET
LI BATT METER
2.2A
2
1
MAIN 00.00V
ENTER
DSCH CURRENT
4.20V
VERSION
H0.000V
L0.000V
2.0V (1P)
1.0A
DSCH CURRENT
VERSION
1.00
1
1.0A
LITHIUM BATTERy METER
1.00
DSCH VOLTAGE
2.0V (1P)
50C
0.00 0.00 0.00 V
2.0V (1P)
3.0V/CELL
DSCH VOLTAGE
0.00 0.00 0.00 V
PROGRAM SELECT
0.00 0.00 0.00 V
3.0V/CELL
0.00 0.00 0.00 V
TVC=YOUR RISK!
2.0V (1P)
2.0V (1P)
ENTER
LI BATT METER
PROGRAM SELECT
MAIN 00.00V
4.20V
TVC=YOUR RISK!
LI BATT METER
10min
H0.000V
L0.000V
MAIN 00.00V
4.20V
TEMPERATURE
2.0V (1P)
H0.000V
L0.000V
10min
CUT-OFF
50C
TEMPERATURE
120min
CUT-OFF
50C
SAVE PROGRAM
120min
10min
ENTER
SAVE PROGRAM
5000mAh
ENTER
14
5000mAh
120min
ON
LI-PO BATTERIES
ON
ON
To select values other than the existing parameters:
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
5000mAh
ON
locate the PROGRAM SELECT LiPo BATT screen. Press the Jog dial to select LiPo.
• Press the Jog dial so the charge current value (A) flashes
11.0V
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
ON
Rotate the Jog dial to go to one of the control screens (BALANCE, CHARGE, FAST
11.0V
0C
ON
• Press the Jog dial to save the value and the voltage value (B) flashes
CHG, STORAGE or DISCHARGE) to do what your battery needs.
32C
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
0C
Correctly connect your lithium battery to the charger (charging connector first and
series (C))
11.0V
32C
balancing connector second). Press the Jog dial and adjust the charging param-
• Press the Jog dial to save the voltage value
ENTER
eters as needed. Press and hold the Jog dial (approximately 3 seconds) until the
0C
If no parameters are flashing, you can rotate the Jog dial to select another program
screen changes to start the battery check/charge sequence.
ENTER
32C
such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
1.00
To start charging, press and hold the Jog dial for 3 seconds.
R: 3SER
ENTER
1.00
CAUTION: If at any time during the charge process the battery pack becomes
CONFIRM
hot or begins to puff, disconnect the battery immediately and discontinue the
1.00
information. If the information after R: (charger) and S: (settings) (A) does not match,
C
charge process as batteries can cause fire, collateral damage and injuries.
L0.000V
press the Mode key and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the Jog dial to confirm.
L0.000V
After confirmation, charging starts and information will show on the LCD screen
(information may vary).
LiIo FAST CHG
L0.000V
5.0A
21.6V(6S)
A
B
C
To select values other than the existing parameters:
• Press the Jog dial so the charge current value (A) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
• Press the Jog dial to save the value and the voltage value (B) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
15
series (C))
LI-PO BALANCE CHARGING
• Press the Jog dial to save the voltage value
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
If no parameters are flashing, you can rotate the Jog dial to select another program
locate the PROGRAM SELECT LiPo BATT screen. Press the Jog dial to go into this
such as CHARGE, BALANCE, STORAGE or DISCHARGE.
menu.
To start charging, press and hold the Jog dial for 3 seconds.
Rotate the Jog dial to go to the LiPo BALANCE screen and set charging param-
eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
dependent on the number of cells in series. For example, with Li-Po batteries these
values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
To select values other than the existing parameters:
• Press the Jog dial so the charge current value (A) flashes
LiPo BALANCE
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
• Press the Jog dial to save the value and the voltage value (B) flashes
5.5A
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
series (C))
• Press the Jog dial to save the voltage value
A
If no parameters are flashing, you can rotate the Jog dial to select another program
such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
16
LI-PO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog dial to
locate the PROGRAM SELECT LiPo BATT screen. Press the Jog dial to go into this
menu.
C
Rotate the Jog dial to go to the LiPo CHARGE screen and set charging parameters.
The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is
dependent on the number of cells in series. For example, with Li-Po batteries these
To select values other than the existing parameters:
values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
• Press the Jog dial so the discharge current value (A) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the discharge current value
LiPo CHARGE
• Press the Jog dial to save the value and the voltage value (B) flashes
4.6A
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
series (C))
• Press the Jog dial to save the voltage value
A
If no parameters are flashing, you can rotate the Jog dial to select another program
such as CHARGE, BALANCE, FAST CHG or STORAGE.
To start discharging, press and hold the Jog dial for 3 seconds.
C
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG
1
NiMH CHARGE
NiCd CHARGE
CURRENT
2.0A
CURRENT
2.0A
NiMH Auto CHARGE
NiCd Auto CHARGE
CURRENT
2.0A
CURRENT
2.0A
(dYn4300)
NiMH DISCHARGE
NiCd DISCHARGE
0.1A
CUT:1.0V
0.1A
CUT: 1.0V
OPERATING yOUR CHARGER
NiMH RE-PEAK
NiCd RE-PEAK
2
2
18 LI-PO STORAGE CHARGING
PROGRAMMING ANd OPERATIONS
NiMH CYCLE
NiCd CYCLE
19 LI-PO DISCHARGE
35 BATTERY MEMORY
DCHG>CHG
1
DCHG>CHG
1
36 SYSTEM SET
NI-MH
NiCd CHARGE
a REST TIME
Pb CHARGE
20 NI-MH BATTERIES
CURRENT
2.0A
b SAFETY TIMER
2.0A
2.0V (1P)
21 NI-MH CHARGING
NiCd Auto CHARGE
c CAPACITY CUTOFF
22 NI-MH AUTO CHARGING
Pb DISCHARGE
CURRENT
2.0A
d KEY BEEP/BUZZER
23 NI-MH DISCHARGE
2.0A
2.0V (1P)
e INPUT POWER LOW CUTOFF
NiCd DISCHARGE
24 NI-MH RE-PEAK CHARGING
f EXTERNAL AND INTERNAL TEMPERATURES
0.1A
Rest Time
CUT: 1.0V
25 NI-MH CYCLE CHARGING
CHG>DCHG
10min
g RESET FACTORY SETTINGS
NiCd RE-PEAK
NI-Cd
h VERSION
SAFETY TIMER
2
26 NI-CD BATTERIES
37 L I BATTERY VOLTAGE CHECKER OPERATION -
ON
120min
27 NI-CD CHARGING
NiCd CYCLE
USING THE BALANCE ADAPTER PORT
Capacity Cut-Off
DCHG>CHG
28 NI-CD AUTO CHARGING
1
38 USB ACCESSORY CHARGER OPERATION
ON
5000mAh
29 NI-CD DISCHARGE
(COMPATIBLE WITH iPhone AND iPod DEVICES)
Pb CHARGE
30 NI-CD RE-PEAK CHARGING
Key Beep
ON
39 TROUBLESHOOTING GUIDE
2.0A
2.0V (1P)
31 NI-CD CYCLE CHARGING
Buzzer
ON
Pb DISCHARGE
PB
Input Power Low
2.0A
2.0V (1P)
Cut-Off
11.0V
32 PB BATTERIES
33 PB CHARGING
Rest Time
Ext. Temp
0C
34 PB DISCHARGE
Int. Temp
CHG>DCHG
10min
32C
SAFETY TIMER
LOAD FACTORY SET
ON
120min
ENTER
After the self tests, the charger will show another screen. The information on this
Capacity Cut-Off
VERSION
screen will vary but will look similar to this:
ON
5000mAh
1.00
DYNAMITE
LiPo BALANCE
Key Beep
ON
0.00 0.00 0.00 V
2.0A
7.4V(2S)
DYN4300
Buzzer
ON
0.00 0.00 0.00 V
Input Power Low
From any screen, press the Mode key to go back to the main menu.
MAIN 00.00V
Cut-Off
11.0V
H0.000V
L0.000V
Ext. Temp
0C
Int. Temp
32C
B
C
d
A. A Li-Fe battery pack is
LOAD FACTORY SET
LI 3S 2.0A 12.59V
balance charging
ENTER
A
B. Battery pack has 3 cells in
BAL 022:43 01082
series
VERSION
1.00
f
E
C. Charging rate is 2.0A (2000mAh)
0.00 0.00 0.00 V
d. Voltage being applied to the battery is currently 12.59V
0.00 0.00 0.00 V
E. Present charge level of the battery is 1082mAh
A
MAIN 00.00V
f. Time elapsed since the charge process started is 22:43 (22 minutes and 43
When the charge cycle starts, the
H0.000V
L0.000V
charger compares the battery to the
seconds)
S:3SER
charger settings. The screen will show
(ENTER)
During charging, the Jog dial can be rotated counterclockwise to show several
the battery and your settings
parameter messages on the LCD screen, including: End Voltage, Input Power Volt-
age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and
Capacity Cutoff.
Rotate the Jog dial clockwise to show the charge voltages for each cell. Press the
Jog dial at any time to return to the Charge Monitor screen. The charger signals
when the charging (or discharging) process is complete (if Buzzer is set to ON).
CAUTION: The Li-Fe program menus are to be used ONLY for the
charging and discharging of Li-Fe battery packs. The charging of other
battery types using these programs will result in damage to the battery or
charger.
CAUTION: Using a charge rate that is not compatible with the battery
capacities may result in damage or malfunction of the charger or
batteries.
B
C
d
A. A Li-Po battery pack is
LI 3S 2.0A 12.59V
balance charging
A
B. Battery pack has 3 cells in
BAL 022:43 01082
series
f
E
C. Charging rate is 2.0A (2000mAh)
d. Voltage being applied to the battery is currently 12.59V
E. Present charge level of the battery is 1082mAh
A
f. Time elapsed since the charge process started is 22:43
When the charge cycle starts, the
S:3SER
charger compares the battery to the
During charging, the Jog dial can be rotated counterclockwise to show several
charger settings. The screen will show
(ENTER)
parameter messages on the LCD screen, including: End Voltage, Input Power Volt-
the battery and your settings
age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and
Capacity Cutoff.
Rotate the Jog dial clockwise to show the charge voltages for each cell. Press the
Jog dial at any time to return to the Charge Monitor screen. The charger signals
when the charging (or discharging) process is complete (if Buzzer is set to ON).
CAUTION: The Li-Po program menus are to be used ONLY for the
charging and discharging of Li-Po battery packs. The charging of other
battery types using these programs will result in damage to the battery or
charger.
CAUTION: Using a charge rate that is not compatible with the battery
capacities may result in damage or malfunction of the charger or
batteries.
To select values other than the existing parameters:
• Press the Jog dial so the charge current value (A) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
• Press the Jog dial to save the value and the voltage value (B) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
series (C))
• Press the Jog dial to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another program
such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
22.2V(6S)
To start charging, press and hold the Jog dial for 3 seconds.
B
C
To select values other than the existing parameters:
• Press the Jog dial so the charge current value (A) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the charge current value
• Press the Jog dial to save the value and the voltage value (B) flashes
• Rotate the Jog dial to INCREASE OR DECREASE the voltage (and # of cells in
series (C))
• Press the Jog dial to save the voltage value
If no parameters are flashing, you can rotate the Jog dial to select another program
such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the Jog dial for 3 seconds.
22.2V(6S)
CAUTION: If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
B
C
charge process as batteries can cause fire, collateral damage and injuries.