Dynamite DYNS2405 Instrukcja obsługi
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Kable i złącza Dynamite DYNS2405. Dynamite DYNS2405 4 stron. Sport brushless esc
FUZE
™
60A Sport Brushless ESC
Instruction Manual
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-
date product literature, visit horizonhobby.com and click on the support tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury
OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to
operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This
product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components
or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation and
maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to
operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
SPECIFICATIONS
Type
Sensorless
Constant/Peak
60A/90A
Resistance
1.7mΩ
Function
Proportional forward, proportional reverse with braking delay
Input Voltage
2-3S LiPo, 6-8 Cell NiMH
BEC Output
6V/2A
Overload Protection
Thermal
Dimensions (LxWxH)
40mm x 32mm x 19mm
Weight
51g
QUICK START GUIDE
Ensure all wiring connections can be reached prior to
mounting.
The quick start setup guide will get you running quickly
Use double-sided foam tape to secure the switch to a
using the ESC's default settings.
convenient location in the vehicle.
1. Mount the ESC and motor in the car.
2. Connect the ESC to the motor.
WIRING
3. Connect the ESC receiver lead to CH2 on your receiver.
Motor Battery
DIAGRAM
4. Ensure the ESC switch is OFF.
5. Connect a fully charged battery.
6. Calibrate ESC to the transmitter.
Steering
7. Set battery chemistry.
Servo
MOUNTING THE SPEED CONTROL
Mount the ESC in the location specified by your vehicle's
CH1
Receiver
CH2
instruction manual. Use double-sided foam tape to secure
Speed Control
ON/OFF SET
the speed control in position.
MOTOR TO ESC CONNECTION
1. Connect the blue motor lead to the blue ESC lead.
2. Connect the yellow motor lead to the yellow ESC lead.
3. Connect the orange motor lead to the orange ESC lead.
If the motor turns in the wrong direction, reverse the connection of any 2 motor wires.
NOTICE: Always disconnect the battery from the ESC when you have finished operating your vehicle. The ESC's switch only
controls power to the receiver and servos. The ESC will continue to draw current when connected to the battery, resulting
in possible damage to the battery through over discharge.
ESC CALIBRATION PROCEDURE
Ensure proper ESC function by calibrating the ESC to your transmitter inputs. The motor should be left connected during
calibration, it will not run during calibration for safety.
1.
Power OFF the ESC.
2.
Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral and the throttle travel
range is at 100%. Disable any special functions such as ABS, etc.
3.
Press the SET button while powering ON the ESC. Release the button as soon as the red LED starts to flash and the
motor emits a beep.
4.
Calibrate the throttle points by pressing the SET button once after each step.
• Set Neutral: leave the throttle at rest, untouched and press the SET button
(1 green flash; 1 motor)
• Set Full Throttle: pull the throttle fully back, then press the SET button
(2 green flashes; 2 motor beeps)
• Set Full Brake/Reverse: push the throttle fully forward, then press the SET button
(3 green flashes; 3 motor beeps)
NOTICE: The motor will NOT run during the calibration procedure.
5.
Power off the ESC. The ESC is calibrated and ready to run.
ESC FUNCTIONS AND MODES
The ESC includes programming options so you can adjust the way your vehicle performs.
Refer to the included settings table to adjust the ESC for your driving conditions.
© 2018 Horizon Hobby, LLC. Dynamite, Tazer, and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC.
ESC PROGRAMMING PROCEDURE
Programming is accomplished using the SET button on the ON/OFF switch.
1.
Connect a fully charged battery to the ESC.
2.
Power ON the ESC using the ESC switch.
3.
Press and hold the SET button for 3 seconds until the green LED flashes, then release the SET button.
4.
Press the SET button once until the green LED blinks once in sequence, indicating programmable value 1 is currently
selected.
Pressing the setup button once more moves to programmable value 2, etc. until the desired programmable value is
reached. The system continues in a 'loop'.
5.
When at the desired menu item, hold the SET button for 3 seconds until the red LED blinks.
The RED flashing sequence indicates the actual setting; for example one flash indicates value 1 is selected, two
flashes indicates value 2, etc..
6.
Press the setup button in sequence to select the desired programmable value. The system continues in a "loop."
7.
Save the setting by holding the SET button for 3 seconds. The motor beeps once.
8.
Power OFF the ESC then immediately power it ON. The setting change is stored.
Only one setting can be stored/saved at a time.
PROGRAMMABLE VALUE
PROGRAMMABLE ITEMS
Basic Items
1
2
Forward/Reverse w/
1 Running Mode
Forward w/ brake
brake
2 Drag Brake Force
0%
5%
3 Low Voltage Cutoff
non-protection
3.0V/Cell
4 Start Mode
Level 1
Level 2
5 Max Brake Force
25%
50%
6 Punch
Level 1
Level 2
DESCRIPTIONS
1.
Running Mode:
- Forward Only with Brake
Intended for competition use, this mode allows only forward and brake controls.
- Forward/Reverse with Brake
This mode is the basic all-around mode, allowing forward, reverse and brake controls. To engage reverse while moving forward,
apply the brake until the vehicle has come to a complete stop, release brake, then apply the brake again. While braking or in
reverse, engaging the throttle will result in the vehicle immediately accelerating forward.
2.
Drag Brake Force
Adjusts the amount of brake automatically applied when the throttle is returned to the neutral position. This simu-
lates the engine braking effect of a full-scale vehicle, allowing improved turn-in and your vehicle's general response
to controls.
3.
Low Voltage Cutoff
Brushless
Motor
This function helps to prevent battery over-discharge. The ESC continuously monitors the battery's voltage. If the
voltage falls below the voltage threshold for 2 seconds, the output power shuts off and the red LED flashes twice
repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries, if the voltage battery
pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery pack; if it is lower than 9.0V, it will be treated as a
2-cell Li-Po battery pack. Example: for a 8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as
a 2-cell Li-Po battery pack and the low-voltage cut-off threshold will be 5.2V (2.6 x 2=5.2).
4.
Start Mode
Sets the initial throttle punch when the car accelerates. Level 1 gives
a very soft initial acceleration and Level 4 gives a stronger initial acceleration.
5.
Max Brake Force
Adjusts the maximum braking force. A higher value provides stronger braking,
but can also cause the wheels to lock, resulting in loss of control of the car.
6.
Punch
Select from start mode Level 1 (Soft) to Level 9 (Very aggressive). If you choose Levels 7–9, use a high quality battery
pack with powerful discharge ability. Without a high quality battery pack, the modes will not give a bursting start
effect. If the motor does not run smoothly (i.e., trembling), choose a better battery or increase the gear rate.
ESC LED STATUS
• I
n the neutral position, no LEDs are lit.
• The red LED lights when the car is moving forward, reversing or braking (sensorless motor).
• The green LED lights when the car is moving forward, reversing or braking (sensored motor).
• The red LED flashes if the battery voltage has reached LVC.
• The red and green LEDs light alternately, indicating the ESC overheating protection is enabled.
• The red LED lights if the receiver signal is incorrect or missing.
Created 04/2018 | 58029
TROUBLESHOOTING GUIDE
SYMPTOM
SOLUTION
Recharge or replace battery
ESC switch powered ON,
Ensure all connections are secure
but no motor function and no
Repair or replace ESC switch or ESC
audible tone
Ensure ESC programming for battery is correct for your battery
Motor turns in the wrong
Change connections of any 2 motor wires to the ESC and ensure motor turns in the
direction
correct direction
When red ESC LED flashes, recharge or replace battery
When red and green LEDs alternate flashing, let motor and ESC cool, changing set up
or gearing to avoid overheating
Ensure ESC programming is correct for voltage and battery
Motor stops
Disconnect battery and let ESC cool
Ensure ESC programming is not causing overheating
Replace gearing
Ensure gearing is not causing overheating
Replace with a high-power battery
Replace battery
Default Settings
Motor accelerates irregularly
Replace damaged wiring
3
4
Adjust or replace gearing
Replace wiring or motor
10%
20%
Motor does not turn
continuously in response to
Ensure good reception between transmitter and receiver
3.2V/Cell
3.4V/Cell
throttle
Level 3
Level 4
Replace ESC
75%
100%
Ensure all ESC programming matches your installed systems requirements for safety
Level 3
Level 4
Ensure all receiver connections are correct and secure
Test the motor apart from the vehicle system and repair or replace motor as needed
Steering servo operates but the
motor does not run
Recharge or replace batteries
Ensure all motor connections are secure
Adjust throttle travel or other throttle settings on the transmitter and re-calibrate the ESC
Ensure all connections to receiver are correct and secure
Steering and motor do not
Refer to manufacturer's instructions to repair or replace transmitter
function
Recharge or replace batteries
Recharge or replace batteries
Ensure ESC programming is correct for voltage and battery
Vehicle does not operate at full
Adjust transmitter settings, such as trim, throttle travel, etc.
speed
Ensure ESC settings are correct for system
Re-calibrate ESC
Adjust transmitter settings, such as trim, throttle travel, etc.
Motor slows but will not stop
Ensure ESC settings are correct for system
Re-calibrate ESC
Repair or replace system antennas
Repair or replace damaged wiring and electrical parts
Move receiver or adjust antenna location so that no metal parts are between the
Decreased transmitter range
antenna and the transmitter
Recharge or replace batteries
Refer to receiver and transmitter manufacturer's instructions to adjust reception or
change to a free and open radio frequency
(DYNS2405)
LIMITED WARRANTY
What this Warranty Covers
call the toll free telephone number referenced in the Warranty
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser
and Service Contact Information section to speak with a Product
that the product purchased (the "Product") will be free from
Support representative.
defects in materials and workmanship at the date of purchase.
Inspection or Services
What is Not Covered
If this Product needs to be inspected or serviced and is
This warranty is not transferable and does not cover (i) cosmetic
compliant in the country you live and use the Product in,
damage, (ii) damage due to acts of God, accident, misuse,
please use the Horizon Online Service Request submission
abuse, negligence, commercial use, or due to improper use,
process found on our website or call Horizon to obtain a Return
installation, operation or maintenance, (iii) modification of or to
Merchandise Authorization (RMA) number. Pack the Product
any part of the Product, (iv) attempted service by anyone other
securely using a shipping carton. Please note that original boxes
than a Horizon Hobby authorized service center, (v) Product not
may be included, but are not designed to withstand the rigors
purchased from an authorized Horizon dealer, or (vi) Product not
of shipping without additional protection. Ship via a carrier that
compliant with applicable technical regulations, or (vii) use that
provides tracking and insurance for lost or damaged parcels, as
violates any applicable laws, rules, or regulations.
Horizon is not responsible for merchandise until it arrives and is
accepted at our facility. An Online Service Request is available at
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
http://www.horizonhobby.com/content/_service-center_render-
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
service-center. If you do not have internet access, please contact
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
Horizon Product Support to obtain a RMA number along with
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
instructions for submitting your product for service. When calling
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
Horizon, you will be asked to provide your complete name,
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT
street address, email address and phone number where you
WILL SUITABLY MEET THE REQUIREMENTS OF THE
can be reached during business hours. When sending product
PURCHASER'S INTENDED USE.
into Horizon, please include your RMA number, a list of the
included items, and a brief summary of the problem. A copy
Purchaser's Remedy
of your original sales receipt must be included for warranty
Horizon's sole obligation and purchaser's sole and exclusive
consideration. Be sure your name, address, and RMA number
remedy shall be that Horizon will, at its option, either (i)
are clearly written on the outside of the shipping carton.
service, or (ii) replace, any Product determined by Horizon to
NOTICE: Do not ship LiPo batteries to Horizon. If you
be defective. Horizon reserves the right to inspect any and all
have any issue with a LiPo battery, please contact the
Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase
appropriate Horizon Product Support office.
is required for all warranty claims. SERVICE OR REPLACEMENT
Warranty Requirements
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER'S
For Warranty consideration, you must include your original
SOLE AND EXCLUSIVE REMEDY.
sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
serviced or replaced free of charge. Service or replacement
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
decisions are at the sole discretion of Horizon.
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
Non-Warranty Service
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
Should your service not be covered by warranty, service
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
will be completed and payment will be required without
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
notification or estimate of the expense unless the expense
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
exceeds 50% of the retail purchase cost. By submitting the
Further, in no event shall the liability of Horizon exceed the
item for service you are agreeing to payment of the service
individual price of the Product on which liability is asserted.
without notification. Service estimates are available upon
As Horizon has no control over use, setup, final assembly,
request. You must include this request with your item submitted
modification or misuse, no liability shall be assumed nor
for service. Non-warranty service estimates will be billed a
accepted for any resulting damage or injury. By the act of use,
minimum of ½ hour of labor. In addition you will be billed for
setup or assembly, the user accepts all resulting liability. If you
return freight. Horizon accepts money orders and cashier's
as the purchaser or user are not prepared to accept the liability
checks, as well as Visa, MasterCard, American Express, and
associated with the use of the Product, purchaser is advised to
return the Product immediately in new and unused condition to
Discover cards. By submitting any item to Horizon for service,
you are agreeing to Horizon's Terms and Conditions found on
the place of purchase.
our website http://www.horizonhobby.com/content/_service-
Law
center_render-service-center.
These terms are governed by Illinois law (without regard to
ATTENTION: Horizon service is limited to Product compliant
conflict of law principals). This warranty gives you specific legal
in the country of use and ownership. If received, a non-
rights, and you may also have other rights which vary from state
compliant Product will not be serviced. Further, the sender
to state. Horizon reserves the right to change or modify this
will be responsible for arranging return shipment of the
warranty at any time without notice.
un-serviced Product, through a carrier of the sender's
WARRANTY SERVICES
choice and at the sender's expense. Horizon will hold non-
Questions, Assistance, and Services
compliant Product for a period of 60 days from notification,
after which it will be discarded.
Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the
Product has been started, you must contact your local distributor
or Horizon directly. This will enable Horizon to better answer your
questions and service you in the event that you may need any
assistance. For questions or assistance, please visit our website
at www.horizonhobby.com, submit a Product Support Inquiry, or
WARRANTY AND SERVICE CONTACT INFORMATION
Country of
Horizon Hobby
Contact Information
Purchase
Horizon Service Center
s
ervicecenter.horizonhobby.
(Repairs and Repair
com/
Requests)
RequestForm/
productsupport@horizonhobby.
Horizon Product Support
United States
4105 Fieldstone Rd
com
(Product Technical
of America
Champaign, Illinois, 61822 USA
Assistance)
877-504-0233
Sales
800-338-4639
Horizon Technischer
Service
Hanskampring 9
European Union
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby
+49 (0) 4121 2655 100
GmbH
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
EU Compliance Statement: Horizon Hobby, LLC
Instructions for disposal of WEEE by
hereby declares that this product is in compliance
users in the European Union
with the essential requirements and other relevant
This product must not be disposed of with other
provisions of the EMC Directive.
waste. Instead, it is the user's responsibility to
A copy of the EU Declaration of Conformity is available
dispose of their waste equipment by handing
online at:
it over to a designated collections point for the recycling of
http://www.horizonhobby.com/content/support-render-
waste electrical and electronic equipment. The separate
compliance.
collection and recycling of your waste equipment at the time
of disposal will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health and
the environment. For more information about where you can
drop off your waste equipment for recycling, please contact
your local city office, your household waste disposal service or
where you purchased the product.
10/15
Address