Galanz DWUK003W Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Zmywarka Galanz DWUK003W. Galanz DWUK003W 14 stron.

Drukuj stronę

7. Maintenance and cleaning

The filter is used to avoid large remnants and other sundries getting inside

Filtering System

the pump.

The filter system consists of a coarse filter, a flat

(Main filter) and a micro filter (fine filter).

1 Flat filter

2 Coarse filter

3 Micro filter

Step 1：Turn the Coarse filter

anti clockwise, and then

lift it up;

Step 2：lift the

NOTE:

If operating from step 1 to step 2, the filter system will be removed; while operating from step 2

to step 1, the filter system will be installed.

Filter assembly

For best performance and results, the filter assembly must be cleaned. The filter efficiently removes

food particles from the wash water, allowing it to be recirculated during the cycle. For this reason, it

is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing

the semicircular filter and cup under running water. To remove the filter assembly, pull on the cup

handle in the upward direction. The entire filter assembly should be cleaned once a week. To clean

the coarse filter and the micro filter, use a cleaning brush. Then, reassemble the filter parts as shown

in the figures above and reinsert the entire assembly in the dishwasher, positioning in its seat and

pressing downward. The dishwasher must never be used without the filters. Improper replacement

of the filter may reduce the performance level of the appliance and damage dishes and utensils.

Food and debris will be trapped by a special jet

on the lower spray arm.

Big debris, such as bone and glass that could clog the

drain will be trapped in the coarse filter.

To remove an item caught in this filter, gently squeeze

the taps on the top of this filter and lift it out.

This filter holds soil and food residue in the sump area

and prevents it from being redeposit on the dishes

during a cycle.

- Inspect the filters for obstructions every time the

dishwasher has been used.

- By unscrewing the coarse filter, you can remove

the filter system. Remove any food remnants and

clean the filters under running water.

Flat

filter up

WARNING!

Never run the dishwasher without the filters in place. When cleaning the filters, be careful not to cause

any damage which could affect the dishwashers performance.

Cleaning the Spray Arms

It is necessary to clean the spray arms regularly for hard

water chemicals will clog the spray arm jets and bearings.

To remove the spray arms, screw off the nut clockwise to

take out the washer on top of the spray arm and remove the

arm. Wash the arms in warm soapy water and use a soft

brush to clean the jets. Replace them after rinsing thoroughly.

Caring for the Dishwasher

To clean the control panel, use a lightly dampened cloth then

dry thoroughly.

To clean the exterior, use a good appliance polish wax.

Never use sharp objects, scouring pads or harsh cleaners

on any part of the dishwasher.

Protect Against Freezing

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

1.Cut off the electrical power to the dishwasher.

2.Turn off the water supply and disconnect the water inlet pipe from the water valve.

3.Drain water from the inlet pipe and water valve. (Use a pan to catch the water)

4.Reconnect the water inlet pipe to the water valve.

5.Remove the filter in the tub and the bottom and use a sponge to remove water in sump.

Cleaning the Door

To clean the edge around the door, you should use only a soft warm, damp rag. To prevent

penetration of water into the door lock and electrical components, do not use a spray cleaner of any

kind.

Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will scratch

the finish. Some paper towels can also scratch or leave marks on the surface.

WARNING!

Never use a spray cleaner to clean the door panel for it could damage the door lock and electrical

components. Avoid using abrasive agents or paper towels because of the risk of scratching or

leaving spots on the stainless steel surface.