Autonics TC4H Podręcznik - Strona 6
Przeglądaj online lub pobierz pdf Podręcznik dla Kontroler temperatury Autonics TC4H. Autonics TC4H 14 stron. Touch switch type temperature controller
Również dla Autonics TC4H: Podręcznik (14 strony), Podręcznik (2 strony), Instrukcja obsługi (2 strony), Skrócona instrukcja obsługi (9 strony), Skrócona instrukcja obsługi (10 strony)
Drukuj stronę
SV setting
※ In case of changing set temperature from 210℃ to 250℃.
① RUN mode(display a current temperature)
Press any key among
② Set value change
mode Change set
value by
keys.
④ Check SV
Flow chart for setting group
①
Press any key among
,
,
,
SV setting
※ 1: It is not displayed for AC/DC power type.
※ If no key entered for 30 sec., it returns to RUN mode automatically and the set value of
parameter is not be saved.
※
This parameter might not be displayed depending on other parameter settings.
① Press any key once in RUN mode, it advances to set value setting group.
② Press
key over 2sec. in RUN mode, it advances to setting group 1.
③ Press
key over 4sec. in RUN mode, it advances to setting group 2.
④ First parameter will be displayed on viewer when it advances to the setting group.
⑤ Press
key over 3sec. in the setting group, it returns to RUN mode.
※ Exception: Press
key once in SV setting group it returns to RUN mode.
※ Press
key again within a sec after return to RUN mode by press
3sec., it advances to the first parameter of previous setting group.
※ Parameter setup
Parameter 2 group → Parameter 1 group →
• Set parameter as the above considering parameter relation of each setting group.
• Check parameter set value after change parameter of setting group 2.
※ Indicator type displays shaded parameter(
※ AL-1 , AL-2 parameter of setting group2 is decided whether to display according by alarm output type.
※ If alarm operation mode[ AL-1 , AL-2 ] of setting group2 is set to AM)_ / SBa □ / LBa □, AHYS parameter is not displayed.
,
,
,
,
,
Run mode
②
2 sec.
Parameter 1group
PAR1
[
3 sec.
④
AL1
AL1 alarm temperature
AL2
AL2 alarm temperature
AT
Auto tuning ON/OFF
P
Proportional band
I
Integral time
D
Derivative time
Manual reset
RSET
(Normal deviation correction)
HYS
ON/OFF control hysteresis
SV setting
) of setting group 2.
Economical PID Control
③ Finish the setup.
Parameter 2group
]
IN-T
Input sensor
UNIT
Temperature unit
IN-B
Input correction
MAvF
Input digital filter
L-SV
SV low-limit value
H-SV
SV high-limit value
O-FT
Control output operation
C-MD
Control type
OUT
Control output type
SSrM
SSR drive output method
T
Control cycle
AL-1
AL1 alarm operation mode
AL-2
AL2 alarm operation mode
AHYS
Alarm output hysteresis
LBaT
LBA monitoring time
LBaB
LBA detection range
DI-K
Digital key operation
Control output MV in case of
ErMV
input break error
key over
LOC
Lock
⑤
③
4 sec.
PAR2
[
]
3 sec.
※1
H-59
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other