Hifonics X1200.4 Skrócona instrukcja instalacji
Przeglądaj online lub pobierz pdf Skrócona instrukcja instalacji dla Wzmacniacz samochodowy Hifonics X1200.4. Hifonics X1200.4 2 stron.
Drukuj stronę
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
Model
Power cable size
X200.2
and fusing
X400.4
It is critical to use the proper power
X800.4
and ground cable. Select the size
listed here for your amplifier model.
X1200.4
Always use high quality copper
X1100.1D
cable. Visit our website for multi amp
X1500.1D
system cable recommendations.
X1900.1D
Be sure to use the proper fuse size
X2200.1D
for each model. Some models require
an external fuse.
X2600.1D
Installation
Disconnect
1
negative battery
terminal
Place terminal in a secure
position so that it won't
accidentally contact the
negative battery post
Run Cables
2
Properly route power,
speaker and RCA cables
through the vehicle.
Mount Amplifier
3
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
Chassis Ground
4
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
Fuse Size
Cable Size
5
8ga
Connection
1-30A atc
2-20A atc
2-30A atc
Attach the chassis ground
cable to the amplifier
2-60A Maxi
4ga
negative terminal. It is
1-60A Maxi
important to make sure this
2-50A Maxi
connection is very tight.
2-60A Maxi
2-100A Maxi
Remote Turn-on
6
1/0ga
Connection
ext - 250A
Attach the remote turn on
wire to the amplifier remote
output of the source unit.
Positive Power
7
Connection
Attach the main power cable
to the amplifier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Signal Input
8
Connection
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
9
Level Control
Bare metal
BRIDGED
LEFT
RIGHT
SPEAKER
OUTPUT
BRIDGED
LEFT
RIGHT
SPEAKER
OUTPUT
INPUT
Turn the LEVEL control completely
LEVEL
counter-clockwise to minimum.
9V
0.2V
PHASE
Speaker
10
Connections
SPEAKER
OUTPUT
Connect the speaker cables to
the speaker output connectors.
Follow the diagram below
that best fits your speaker
configuration.
Stereo
Bridged
BRIDGED
BRIDGED
LEFT
LEFT
RIGHT
RIGHT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
Monoblock
Monoblock
single woofer
BRIDGED
LEFT
RIGHT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
Positive Battery
11
Connection
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
SPEAKER
OUTPUT
terminal.
Be prepared to disarm your vehicle's alarm and
to enter your radio / source unit code.
Re-connect
12
Negative Battery
Terminal
SUBSONIC
Re-connect the negative
XOVER
battery terminal making sure it
is securely tightened.
15
35Hz
FULL
HP
LP
LPF
SPEAKER
OUTPUT
BRIDGED
LEFT
RIGHT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
multiple woofers
BRIDGED
LEFT
RIGHT
BRIDGED
LEFT
RIGHT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT