Galaxy G9000S Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Produkt hydrauliczny Galaxy G9000S. Galaxy G9000S 6 stron. Instantaneous electric shower

Drukuj stronę

11. Slide soap dish down the

rail to required position.

12. Firmly attach flexible hose to

the showerhead making sure

sealing washer is in place.

NOTE the adjustable slider grips the

conical end of the hose, not the

handle of the showerhead.

Maintenance:

Clean regularly with a non-abrasive liquid

bathroom cleaner.

SECTION

COMMISSIONING THE

SHOWER

1. Make sure that the electrical supply has

been isolated at the double pole isolating

switch.

2. Turn the top power selector knob to the

'Cold' setting (Solid Blue Symbol).

3. Turn the bottom temperature control

knob anti-clockwise to the full cold position.

4. Ensuring the water supply is fully on at

the mains stop cock and isolating service

valve (if fitted), check that water is not

leaking from the bottom of the case.

. Switch on the electrical supply at the

double pole switch. The 'Power' neon

indicator will light.

6. Press the START/STOP button. Check

that water flows freely from the shower

within a few seconds. The water from the

showerhead will be at full force and at a

cool temperature.

7. Rotate the bottom temperature control

knob slowly clockwise fully. This will

gradually reduce the flow with the water

temperature remaining cool.

8. Return the knob anti-clockwise to

maximum flow.

9. Now t

urn the top power selector knob to

the 'Low' setting (Outline Red Symbol).

Allow a few seconds for the warmer

temperature to reach the showerhead -

this shows that the 'Low' power setting is

operating correctly.

10. Now turn the top power selector knob

to the 'High' setting (Solid Red Symbol).

The temperature at the showerhead will

rise further - this shows that the full power

setting is operating correctly.

11. Turn the bottom temperature control

knob clockwise for hotter water and

anti-clockwise for cooler water. Allow a few

seconds between selections - for the

temperature change to reach the

showerhead.

NOTE. When the temperature is

changed the flow rate alters.

12. Push the START/STOP button to stop

the flow.

13. Switch of pull-cord or wall mounted

switch.

SECTION

OPERATING THE SHOWER

1. Switch on pull-cord or wall mounted

switch. The 'Power' neon will illuminate

indicating the switch is on.

2. Press the START/STOP button for

immediate water flow.

3. Select your power setting using the top

control. The shower has three positions

'Cold', 'Low' power and 'High' power.

'Cold' setting (Solid Blue Symbol):

Adjustment of the flow control on

this setting will only alter the flow of

water not the water temperature.

'Low' setting (Outline Red Symbol):

This is the low power setting for

economy during warmer months or

when a cool shower is required.

Temperature adjustment is via the

bottom temperature control.

'High' setting (Solid Red Symbol):

This is the full power setting.

Temperature adjustment is via the

bottom temperature control.

4. Wait a few seconds for the warmer

water to reach the handset.

5. If necessary turn bottom 'Temperature'

control knob slowly to obtain desired

showering temperature. Again, waiting a

few seconds after each adjustment in

temperature to reach the handset.

Note:

To adjust the shower temperature.

The water temperature is altered by

increasing or decreasing the flow rate

of water through the shower unit via

the temperature control.

To increase the shower temperature

Turn the temperature control knob

clockwise, this will decrease the flow

of water and increase the shower

temperature.

To decrease the shower temperature

Turn the temperature control knob

anti-clockwise, this will increase the

flow of water and decrease the shower

temperature.

6. To turn off the shower unit press the

START/STOP button.

COLD

HIGH

LOW

COOLER

WARMER