Galaxy Audio TQ6 Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Głośniki Galaxy Audio TQ6. Galaxy Audio TQ6 2 stron. Battery powered traveler quest pa system

Drukuj stronę
GAL A X Y AUDIO
Battery Powered Traveler Quest PA System
Included Components
1.
TQ6 x1
2.
Remote x1
3.
IEC Power Cable x1
4.
Quick Start Guide x1
Setup
1
Connect power cable to TQ6, connect
other end to a power outlet to charge
immediately. Once charged, the TQ6 can
be operated on AC or Battery Power.
Operation
1
Start with the Master Level set about
mid-way, and the Tone set mid-way
between Treble and Bass. All other level
controls should be turned down (counter-
clockwise to lower, clockwise to increase).
6
MP3 Player Power/Modes: Power on the
built-in MP3 player by pressing and
holding the Power/Mode button. Press
Mode button to switch between SD, USB,
and Bluetooth modes.
1.
2.
2
Connect your microphone to CH1 with
an XLR Cable, or connect a Stereo Line
Level source to the CH2 RCA inputs.
2
Power on the TQ6 by pressing the
power switch into the ON position. The
Power LED will light up.
7
MP3 Player Skip/Volume: Skip forward or
backward between tracks by pressing the
skip buttons. Holding the buttons down
will increase or decrease the volume.
The level is also controlled by the MP3
Level knob.
3.
3
The 1/4" Line Output can be used to
send the TQ6 audio to another sound
system or recorder.
3
Level control: Use the Channel Level
control to raise your input to the desired
level. If needed, the Master Level can
be raised.
8
MP3 Player Repeat: Pressing the
Repeat button once will repeat the current
track. Pressing a 2nd time will repeat a
folder. Pressing a 3rd time will repeat all.
Press once more and the repeat function
will be turned off.
4.
GAL A X Y AUDIO
Q uick Start Guide
TQ6
Battery Powered Traveler Quest PA System
Included Components
1.
1.
2.
3.
4.
TQ6 x1
2.
Remote x1
3.
IEC Power Cable x1
4.
Quick Start Guide x1
Setup
Stand Mounting
(Optional)
1
2
3
1
2
Connect power cable to TQ6, connect
Connect your microphone to CH1 with
The 1/4" Line Output can be used to
Lift the TQ6 over the speaker stand
Bring the TQ6 down onto the speaker
other end to a power outlet to charge
an XLR Cable, or connect a Stereo Line
send the TQ6 audio to another sound
and align the speaker pole with the pole
stand gently until it is fully inserted.
immediately. Once charged, the TQ6 can
Level source to the CH2 RCA inputs.
system or recorder.
socket on the bottom of the TQ6.
be operated on AC or Battery Power.
Operation
1
2
3
4
5
Start with the Master Level set about
mid-way, and the Tone set mid-way
Power on the TQ6 by pressing the
Level control: Use the Channel Level
To adjust the Tone, turn the Tone knob
Raise the Echo Level to add echo to the
between Treble and Bass. All other level
power switch into the ON position. The
control to raise your input to the desired
clockwise for more Bass, or turn the knob
mic input source.
controls should be turned down (counter-
Power LED will light up.
level. If needed, the Master Level can
counter-clockwise for more Treble.
clockwise to lower, clockwise to increase).
be raised.
6
7
8
9
10
MP3 Player Power/Modes: Power on the
MP3 Player Skip/Volume: Skip forward or
MP3 Player Repeat: Pressing the
MP3 Player Play/Pause/Folder: Pressing
MP3 Player Bluetooth: In Bluetooth
built-in MP3 player by pressing and
backward between tracks by pressing the
Repeat button once will repeat the current
Play/Pause will either play or pause the
mode, pairing is activated. Make sure
holding the Power/Mode button. Press
skip buttons. Holding the buttons down
track. Pressing a 2nd time will repeat a
audio. Press and Hold the button for the
your Bluetooth enabled Smart Device is
Mode button to switch between SD, USB,
will increase or decrease the volume.
folder. Pressing a 3rd time will repeat all.
Folder function. You can switch between
on. Find the TQ6 in the device list, then
and Bluetooth modes.
The level is also controlled by the MP3
Press once more and the repeat function
folders in an SD or USB device.
select it to pair.
Level knob.
will be turned off.
Stand Mounting
(Optional)
1
Lift the TQ6 over the speaker stand
and align the speaker pole with the pole
socket on the bottom of the TQ6.
4
To adjust the Tone, turn the Tone knob
clockwise for more Bass, or turn the knob
counter-clockwise for more Treble.
9
MP3 Player Play/Pause/Folder: Pressing
Play/Pause will either play or pause the
audio. Press and Hold the button for the
Folder function. You can switch between
folders in an SD or USB device.
Quick Start Guide
TQ6
2
Bring the TQ6 down onto the speaker
stand gently until it is fully inserted.
5
Raise the Echo Level to add echo to the
mic input source.
10
MP3 Player Bluetooth: In Bluetooth
mode, pairing is activated. Make sure
your Bluetooth enabled Smart Device is
on. Find the TQ6 in the device list, then
select it to pair.