Autopage RF-305 Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Alarm samochodowy Autopage RF-305. Autopage RF-305 2 stron. Part 1
Również dla Autopage RF-305: Programowanie nadajnika (1 strony)

Drukuj stronę

OPERATION INSTRUCTIONS

REMOTE CONTROL TRANSMITTER OPERATION

Your AutoPage Security System comes with two 5 -button Remote Control

Transmitters that feature a sophisticated code hopping system that will prevent

illegal use of a code grabber with an attempt to record and steal your transmitter

codes.

LOCK – ARM & LOCK

To arm your Security System, press the LOCK button once. The siren will chirp

(1) time and the vehicles parking lights will flash (1) time indicating that the

Security System is now armed. The vehicles doors will lock upon arming when

interfaced with the Security System.

UNLOCK – DISARM & UNLOCK

To disarm your Security System, press the UNLOCK button once. The siren will

chirp (2) times and the vehicles parking lights will flash (2) times indicating that

the Security System is now disarmed. The vehicles doors will unlock upon

disarming when interfaced with the Security System.

DELETING THE ARM/DISARM CHIRP

When attempting to arm or disarm your Security System, you have the option of

temporarily muting the siren chirp sound. To perform this function, simply

depress both LOCK & UNLOCK buttons on the Remote Control Transmitter at

the same time. No chirp sound will be heard, arm / disarm confirmation will be

through the vehicles parking lights only.

REMOTE PANIC FUNCTION

The Remote Control Transmitter may be used as a remote panic switch that will

activate the Security Systems siren and vehicles parking lights in case of an

emergency. To activate the PANIC function, press and hold the * button on the

Remote Control Transmitter for (3) seconds. The siren will sound and the

vehicles parking lights will flash continuously. To cancel the PANIC function,

press the lock / unlock button on the Remote Control Transmitter.

AUXILIARY FUNCTION (OPTIONAL

)

You may use the EXT1 button on your Remote Control Transmitter for a

separate function. For example, if your vehicle is equipped with an electronic

trunk release, the Security System can be interfaced with it and can electronically

release your trunk by pressing the EXT1 button for 2 seconds on the Remote

Control Transmitter.

REMOTE CONTROL TRANSMITTER PROGRAMMING

In the event, you should need to add or replace a Remote Control Transmitter, it

is important that you follow the instructions below.

Note:

Each step must be performed within 10 seconds of the previous step

otherwise the system will exit the programming mode.

Enter:

a. Turn the vehicles ignition to the "ON" position

b. Push the valet switch 3 times. There will be 1 long chirp and 1 short chirp

c. You are now ready to program the Remote Control Transmitter(s).

Programming the Remote Control Transmitters:

a. Press any button on the first transmitter. There will be 1 short chirp.

Within 10 seconds push any button on the second transmitter. There

will be 2 short chirps.

Exit:

a. Turn the vehicles ignition to the "OFF" position, Or

b. Leave for 10 seconds; there will be 3 long chirps to confirm exit.

Note:

The Security System will only retain the last 4 Remote Control

Transmitters programmed. If the Transmitter memory is exceeded, the

Security System will start deleting Transmitters from memory in

chronological order.

SECOND VEHICLE REMOTE TRANSMITTER PROGRAMMING

Your AutoPage Security Systems Remote Control Transmitter can be utilized to

control a second vehicle equipped with an RF-305 or RF-405. To program the

Remote Control Transmitter to a second vehicle, follow the instructions for

Remote Transmitter Programming. All programming parameters will be the same

except for the following:

Prior to pushing any button on the Remote Control Transmitter. Select the

Green side shift button first.

Once the Green side shift is pressed the LED on the Remote Control

Transmitter will illuminate for 3 seconds.

While the LED is illuminated, press any button on the Remote Control

Transmitter.

CHANGING THE REMOTE CONTROL TRANSMITTER BATTERY

The Remote Control Transmitters come with (1) miniature 12-volt battery. Under

normal use this battery should have a life of approximately one year. If you

should need to replace your battery you may want to return to your installing

dealer. You may also wish to change the battery by yourself. When purchasing

the battery be sure to purchase any of the following: GP23A, #EL12, #VR22 or

Radio Shack #23-144.

To replace the battery, carefully remove the case screw located on the bottom of

the Remote Control Transmitter where the key ring attaches to the case. Use a

miniature #1 Phillips head screwdriver!

After removing the screw, carefully pop open the plastic case. Before removing

the battery note the direction of its "+/-" terminals. Install the new battery exactly

the same way using caution not to bend the battery contacts. Replace the case

cover and insert and tighten the screw. Do not over tighten! Test the Remote

Control Transmitter.

SYSTEM OPERATION

OVERRIDE FUNCTION

The OVERRIDE FUNCTION may be used if the Remote Control Transmitter is

lost or inoperative. To operate, enter the vehicle (alarm will sound), turn the

vehicles ignition to the "ON" position and push the valet/override switch until

alarm stops sounding. The alarm is disarmed & reset. Have your Remote Control

Transmitter serviced or replaced.

VALET FUNCTION

The alarm has a valet or stand-by mode that can be used when the vehicle is

being serviced or valet parked. To activate the valet, turn the vehicles ignition to

the "ON" position, then push and hold the valet/override switch for 2 seconds or

until the Security Systems LED turns ON solid. Turn the vehicles ignition to the

"OFF" position; your vehicle is now in valet mode. To reactivate, repeat the

above procedure noting the system LED will now turn OFF.

Note:

If your vehicle has the Keyless Entry option installed, you can still lock

and unlock your doors with Remote Control Transmitter while in the

Valet Mode.

PASSIVE/MANUAL OPERATION

Manual Arming / Disarming is controlling your security system via the Remote

Control Transmitter. This Security System is equipped with an optional Passive

Arming feature, which allows the Security System to arm 30 seconds after the

last door is closed. Operation is as follows.

Turn the vehicles ignition to the "OFF" position and exit the vehicle.

After all entrances are closed, the Security Systems LED will flash fast for

30 seconds. If you re-open any door, the Security Systems LED will stop

flashing. It will begin flashing again once the vehicles door is closed.

After the 30 second timer has elapsed, the Security System will

automatically "ARM". The siren will chirp (1) time and the vehicles parking

lights will flash (1) time.

Note:

If the vehicles door locks have been interfaced to the Security System,

the doors will automatically lock after the passive arming cycle has

been completed. If this feature is not desired, see your local dealer

and have the Security System re-programmed to eliminate passive

door locking.

AUTOMATIC REARMING (OPTIONAL)

If this feature is selected, the Security System will automatically re-arm itself 60

seconds after disarming with the Remote Control Transmitter. Automatic rearm

will cancel if any door is opened before the 60 second timer has elapsed.

IGNITION CONTROL DOOR LOCKS (OPTIONAL)

If the vehicles door locks have been interfaced to the Security System, the

Security System will automatically lock the vehicles doors when the ignition is

turned "ON" and unlock the vehicles doors when the ignition is turned "OFF".

Note:

If any door is open when the vehicles ignition is turned "ON", the

Security System will not automatically lock the vehicles doors.

LED STATUS INDICATOR

LED OFF: Security System is disarmed

LED ON: Security System is in valet mode

LED FAST FLASHING: Automatic arming timer is counting down

LED FLASHING: Security System is armed