DCP LogIT DataMetern1000 Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Przyrządy pomiarowe DCP LogIT DataMetern1000. DCP LogIT DataMetern1000 13 stron.

Drukuj stronę

Buttons and sockets

POWER

SENSOR SOCKETS

SOCKET

❷

!!❷

DBus

socket

Meter keys:

OFF

RESET

RED

❏ ❏

LogIT

•BUTTONS - the exact function of buttons change depending on what you are

doing but is shown on the screen above each button

To RESET DataMeter both Hidden reset buttons have to be pressed at the same

time - see page 9 (These are hidden to prevent accidental use).

•SENSOR SOCKETS - all 3 sockets can accept any Microsense sensor which they

automatically identify and calibrate in standard SI units.

•DC POWER SOCKET - Plugging the special LogIT power pack into this socket

charges DataMeter and also allows you to use it at the same time if required.

16-24 hours is required for a full charge (see page 9).

•DBus SOCKET is for connecting DataMeter to a computer for transfer of data,

updating system software or control facilities.

!!!!!!!!!!❷

!❷

LOG

'Hidden'

Reset keys

RESET

Press both

to reset

GREEN

BLUE

D D D D a a a a t t t t a a a a M M M M e e e e t t t t e e e e r r r r 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Sensor product range

The following is a list of DataMeter compatible sensors and adapters as available

in August 1999 - check our web site www.dcpmicro.com or contact your dealer.

•Temperature

General HiTemp sensor - basic flexible wire ended (-10 to +110˚C)

ProTemp sensor - robust stainless steel 180mm probe (-30 to +130˚C)

K-Type thermocouple adapter for standard K type's (-50 to +1200˚C)

•Environment

Sound Level sensor - compact design with a range of 50 - 100dB

General purpose humidity sensor (10 - 90% R.H.)

HumiPro fast responding wide range humidity sensor (1-100% R.H.)

Air Pressure sensor - absolute / barometric pressure sensor (0-200kPa)

Light level sensor+lens; fast response light sensor with optics (0-100%)

LUX light level sensor - wide range reading in LUX (0 - 25000 LUX)

•Electrochemistry

pH amplifier adapter to enable standard pH electrodes to be used

Dissolved Oxygen probe set with probe and amplifier (0 - 200% sat)

Conductivity probe set including probe and amplifier (10µS - 20mS)

Redox adapter - for standard Redox potential electrodes

•Health

Heart Receiver for wire-less 'Polar Beat'

Pulse Monitor with ear clip

•Movement & Position

Position sensor - measures rotation 0-340˚ with very low torque

LogIT Ranger - Ultrasonic sensor module for dynamic speed & position

•Digital sensors and switches

Light gate set - pair of complete light gates for timing investigations

Light Switch - a switch to detect light - make your own light gate

Infra Red source - designed to act as source for Light switch

Push Switch - for manually triggering timing events

Reflective switch - built in IR source for tachometer work etc

Magnetic Switch - triggers on magnetic field (magnet supplied)

•Voltage, Current and Magnetic field

Voltage Measurement probe with set of plugs & probes (+/- 25V DC)

Current measurement set with set of plugs & probes (+/-1A DC)

Magnetic Field probe-electromagnetic investigations (-90mT/+90mT)

•Adapters

Designer sensor set with analogue & digital adapters for own designs

1 Volt sensor adapter - for using other equipment/sensors (0-2.5V DC)

100mV voltage adapter - with BNC socket (-100mV to +100mV DC)

Balance interface - for balances with suitable output to log mass

Ohaus Scout/Fisher Balance adapter for low cost balances

4-20mA Current loop adapter (Other adapters are available)

•Accessories

Remote Mark Switch, Extension cables and mounting clips available

Control accessories including Control Relay, LED, Buzzer and SwitchIT