Gallien-Krueger 2000RB Instrukcja obsługi - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Gallien-Krueger 2000RB. Gallien-Krueger 2000RB 12 stron.
Drukuj stronę
Front Panel Features
(1) INPUT JACK
1/4'' phone jack to plug in active or passive basses with a
shielded cord
(2) -10 dB PAD
This switch should be pressed if the CLIP(3) light stays on
continuously. It may be necessary to "pad" the input if you are
using a bass with active electronics or very high output.
(3) CLIP
LED indicator which lights when the input stage is being over-
driven. If -10dB PAD (2) is pressed and CLIP(3) still stays lit,
turn down the volume on your bass.
(4) TUNING MUTE
Switch that mutes all outputs from the amplifier (speakers, direct
and balanced outs) so you can tune up without sending signal to
the audience or the P.A.. Tuning mute can be footswitch
controlled by using a G-K RF2 footswitch, which will leave both
hands free to tune your instrument. To control TUNING MUTE
by footswitch, TUNING MUTE (4) switch must be "in"
(5) LED INDICATOR
Lights when TUNING MUTE is activated.
(6) VOLUME
Controls signal level at the beginning of preamp stages.
Volume should be turned up until the CLIP(7) light comes on
when you're hitting your loudest notes. At this setting you will
have the optimum signal/noise ratio. Remember that your settings in
the VOICING FILTER and ACTIVE EQUALIZATION sections
can also cause clipping. IF this occurs, re-adjust VOLUME as
explained above.
(7) CLIP
LED indicator that lights when either VOLUME, VOICING
FILTER, OR ACTIVE EQUALIZATION stages are being over-
driven.
(8) BOTTOM
Voicing filter which boosts or cuts +/-12dB at very low frequencies
(20Hz center freq.). Boost this control if you want to add more
low-bass response. Or, keep it turned down if you want a tighter,
less "boomy" bottom end.
(9) CONTOUR
Voicing filter that boosts highs (4kHz) and lows (80Hz), while
dropping out mids (600Hz).
between half and maximum to create a "round" or "hi-fi" sound.
Use lower settings for a "flatter" response.
Most players use this control
(10) PRESENCE
Voicing filter that boosts high frequencies (6.5kHz center freq.)
by as much as 12dB. This control adds "edge" to help you cut
through the mix.
(11) - (14) ACTIVE EQUALIZATION
Four highly active tone controls, TREBLE, HI MID, LO MID,
AND BASS. Each band of EQ creates wide tonal variations
without affecting the other bands.
(15) BOOST 1
A post EQ gain stage using GIVE Technology which adds
"growl" as you turn it up. The RF2 footswitch allows you to
switch between BOOST1 and BOOST 2.
(16) LED INDICATOR
Lights when you have footswitched into the BOOST 2 mode.
(17) BOOST 2
A post EQ gain stage like BOOST 1, except this stage has higher
gain for "lead-bass" or solos. Use BOOST 2 with LEVEL (18)
to create the desired amount of overdrive. Note: You can only
access the BOOST 2 section via the RF2 footswitch.
(18) LEVEL
Determines the level coming out of BOOST 2 section. Used to
set a different volume level for solos.
(19) AUX LEVEL
Controls signal level coming from STEREO AUX IN (20).
Creates effects blend (dry vs. wet) when used in a "parallel"
effects loop. Can also be used to mix in any stereo source such
as tape or CD.
(20) LEFT - LOW - BRIDGE
Master volume that controls output level to speakers. In "Stereo
Mode", controls output of LEFT channel. In "Biamp Mode"",
controls output of LOW frequency amplifier. In "Bridge Mode",
controls output level of the entire amplifier.
(21) RIGHT-HIGH
Master volume that controls output level to speakers. In "Stereo
Mode", controls output of RIGHT channel. In "Biamp Mode",
controls output of HIGH frequency amplifier.
Mode", this control is inactive.
(22) POWER SWITCH
(23) & (26) PROTECT
LED indicators that light when L&R channels power up, power
down, or whenever the FAULT DETECTION CIRCUITRY
relays have disconnected the 2000RB from your speakers.
(24) & (27) CLIP
LED indicators that light when L&R channels are clipping.
(25) & (28) POWER
LED indicators that light when L&R channels are in normal
4
operation.
In "Bridge