Galvamet SHARP Instrukcje instalacji, obsługi i konserwacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcje instalacji, obsługi i konserwacji dla Okap wentylacyjny Galvamet SHARP. Galvamet SHARP 12 stron.

Drukuj stronę

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS FOR COOKER HOOD MODEL SHARP

Exhausting cooker hood. The equipment is constructed in accordance with European Standards and with the requirements included in the following Directives: 2006/95EC ( Low Voltage

Directive), 2004/108 (Electromagnetic Compatibility).

INSTALLATION

Read the instruction manual before installing and/or using the hood.

The unit must be fitted at a distance of at least 65 cm. from the cooking hob. If the

mounting instructions of the gas cooker indicate a wider distance, respect it. The unit must

not be mounted above cookers fitted with top radiant plate.

Respect all the air discharge regulations.

The air must not be discharged in a pipe used to discharge exhaust fumes produced by

gas-fed equipments or fuel-fed equipments (this does not apply to filtering hoods).

The room must be adequately ventilated when the hoods is used together with other gas-

fed or fuel-fed equipments.

For an easy access, it is advisable to move possible furniture under the installation area.

Installation of the hood onto the wall.

The hood is equipped with all the necessary fastenings for its installation, which are

suitable for most surfaces. Anyway ask a professional to verify that the installation surface

is strong.

Installation must be carried out by qualified installers according to present regulations.

•

Drill the wall as indicated on the drawing 1

•

Insert the hood and fix it with the fixing supports (A)

•

Open the light covers (B) as indicated on the drawing and fix the supports with the

screws underneath the light covers

ELECTRICAL CONNECTIONS

This equipment must be connected to a grounding plant.

Two types of electrical connection can be used:

Using a standard plug to be connected to the power cable and inserted in a mains

socket which must be accessible (so that the plug can be disconnected when

servicing is carried out). Make sure that the plug is accessible also after the

complete installation of the equipment.

By means of a fixed mains connection, fitting a bipolar switch, which ensures the

disconnection, with an opening distance of the contacts allowing a complete

disconnection on the conditions of the overvoltage III category, according to

installation regulations. The ground connection (yellow-green wire) must not be

interrupted.

Refer to the plate inside the hood for the mains voltage and frequency ratings.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoida hazard.

EMPLOYMENT

This cooker hood can be employed as exhausting or filtering.

Exhausting (external evacuation). Kitchen smokes are driven outside through a flue

joined to the exhaust pipe flue connector.

This pipe must not under any circumstances be connected to cooker, boiler or burner

exhaust pipes, etc.

Filtering (inside recycling). Smokes pass through the activated charcoal filter (Picture 2 -

C) to be cleaned and recycled in the kitchen.

In this case you should not install the exhaust pipe without curve.

OPERATION

The hood is supplied with a multispeed motor.

The hood should be run at low speed under normal conditions and at higher speeds only

when there is a heavy build-up of fumes or odours.

Ideally, the hood should be switched on as soon as cooking is started and then kept on

until all odours have been eliminated.

The controls consist of touch screen commands. Press TL to turn on the light, press T1 to

swich on the hood at first speed and to switch off the aspirator, press T2-T3-T4 to select

functioning speeds.

Adjustable and delayed self switching off

Choose the desired speed while the hood is working, then keep the speed button pressed

until it starts blinking. This button corresponds to the desired self switching off minutes.

Please keep in mind that:

T1 corresponds to 5 minutes

T2 corresponds to 10 minutes

T3 corresponds to 15 minutes

T4 corresponds to 20 minutes

Filters maintenance reminder

Aluminium anti-grease filters

Once the hood is switched off, after 30 hour functioning, all the leds of the speed buttons

switch on with a fixed light for 30 seconds to remind that aluminium anti-grease filter need

cleaning.To set the timer to zero keep the button T4 pressed with the aspirator switched

off, otherwise the timer will remain set on 30 hour functioning and the reminder will occur

again when the hood is switched off again.

Charcoal filter (for filtering hoods)

Once the hood is switched off, after 120 hour functioning, all leds blink for 30 seconds to

remind that the charcoal filter need cleaning.

To set the timer to zero keep the button T4 pressed with the aspirator switched off,

otherwise the timer will remain set on 120 hour functioning and the reminder will occur

again when the hood is switched off again.

230-240 Vac - 50 Hz

MAINTENANCE

Always disconnect the hood from the mains before carrying out any maintenance or

cleaning operation.

Particular attention should be paid to the metallic anti-grease filters that are designed to

trap particles of fat contained in the fumes. The metallic anti-grease filters must be washed

at least once a month with detergent in hot water (or in the dish-washer).

ATTENTION: the grease collected in the filters can easily catch fire and it is therefore

extremely important to clean the metallic filters on a regular basis as per instructions.

The activated charcoal filters are designed to collect unpleasant odours in the cooking

fumes. The air is then released purified in the environment. The charcoal filters must not

be washed, but replaced 2 or 3 times a year, depending on how much the hood is used.

New filters are to be requested directly to the manufacturer.

In order to replace the activated charcoal filters, turn the filters until they unfasten from

aspirator.

Invert the operation in order to install the new charcoal filters.

In order to remove the remaining glue or any impurity, the cooker hood must be cleaned

immediately after installation and after having removed the protective film.

The cooker hood must be cleaned frequently both internally and externally (at least once a

month).

Do not let dirt gather on the inner and outer surfaces of the hood.

To clean the exterior of the hood do not use either acid or basic products, or abrasive

sponges.

Clean the hood with a sponge dampen in warm water and a little quantity of neutral

detergent (for example dishwasher detergent), in order to remove possible particles of

grease.

Rinse with a damp cloth, removing all the detergent carefully, following the satin finish

direction on the steel surface.

Drying is very important, especially in areas where water is particularly hard and leaves

limestone.

To replace the lamp dichroic just pry with a screwdriver (Pic.3)

Replace the lamp only with an analogous one (halogen max. 20 W, 12 Volts).

WARNINGS

The present instruction manual is an integral part of the appliance itself, therefore it must

be carefully kept and ALWAYS accompany it, even in case of its assignment to another

owner or user or in case the cooker hood is moved to another installation plant.

Any eventual adjustment to the electrical system, which may be necessary to install the

cooker hood, must be carried out only by competent people. Any repair carried out by no

competent people may cause damages. For any repair or needed technical action make

reference to a Technical Assistance Center, which is authorized to carry out the

replacement of the spare parts.

Always make sure that all the electrical parts (lights, exhaustion unit) are disconnected

when the appliance is not in use.

By storms take off the main switch of the house electrical system.

The using of the cooker hood must not be other than the use of exhausting units for

cooking damps on domestic kitchens. The manufacturer does not accept any liability for

damages caused by people, animals or things, by installation and maintenance mistakes

or by any illegitimate use.

Make sure that the voltage (V) and the frequency (Hz) ratings indicated on the plate

inside the cooker hood correspond to the ones available in the installation place.

We remind that the use of products functioning with electrical energy implies the

observance of some essential security rules, as follows:

•

This equipment is not intended for people (children included) with reduced mental

or motor capacities, with lack of experience or knowledge, unless they are

supervised or unless a person responsible for their security, gives them instructions

regarding the use of the equipment. Children must be supervised in order to be

sure that they do not play with the equipment.

•

Any cleaning action is forbidden if the appliance hasn't been disconnected from the

main power supply and if the main switch of the house electrical system is not off. If

cleaning is not carried out according to these instructions, a fire may break out.

•

Do not pull, take off or twist the cable coming out from the appliance, even though

this has been disconnected from the main power supply.

•

Do not sprinkle or throw any water directly on the appliance.

•

Do not stick any sharp tool inside the exhausting holes and into the air discharge.

•

Do not take out the filters in order to reach the internal sides of the appliance in

case the main switch of the house electrical system is not off.

•

Do not singe or flambé directly underneath the cooker hood. Take particular care

when frying to ensure that the oil does not catch fire.