Coram Showers 01746 Podręcznik

Przeglądaj online lub pobierz pdf Podręcznik dla Armatura łazienkowa Coram Showers 01746. Coram Showers 01746 2 stron.

Drukuj stronę

13mm

ø 3

10mm Max

Mark off drill hole positions on the wall and on the enclosure with a pencil. Drill 6.5mm holes 30mm

deep in the wall and push fit wall plugs. Drill 3mm holes in the inside face of the enclosure frame (not too

deep). Fix using 25mm screws + washer in the wall and 13mm screws + washer in the enclosure. Push fit

support bracket end covers.

Push fit wall channel covers on the inside. From the outside only, apply sealant to the bottom of the

enclosure and 50mm up the wall channels and corner posts as shown.

Cleaning and Maintenance

After each use the glass should be wiped down with a window squdgee and the framework wiped dry. This will reduce the build up

of limescale and water marks on the glass and framework. DO NOT use bleach, scouring powders, solvents or other aggressive

cleaning agents which may damage the framework.

To ensure the doors continue, the top and bottom runners should be lubricated regulary. This should be done using a silicone wipe,

These can be purchased from Customer Care if required.

In some instances mould spores may build up under the glazing seal of the unit. The mould spores are most commonly black or

red in colour. It is possible for a qualified person to remove the glazing seal to clean and replace. Please contact Customer Care for

advice. Mould build up is not covered by the guarentee.

Toughened Safety Glass is twice as strong as untoughened glass. However it is still possible for it to shatter. Care should be taken

when opening and closing the door panels so not to stress the glass.

Stressed glass may shatter at anytime and not necassarily at the time of stress.

Packaging: The cardboard and polythene parts of this packaging can be recycled

End of life: This product contains materials such as aluminium and glass which can be recycled

Please contact your local authority to find your nearest recycling centre

CORAM SHOWERS LTD

Stanmore Industrial Estate, Bridgnorth, Shropshire WV15 5HP, UK • Tel: +44 (0) 1746 766466 • Fax: +44 (0) 1746 764140

Fit support bracket ends to brackets

using 13mm screws. Fit wall brackets

where shown (plan view).

25mm

ø 3

50mm

RECYCLING

www.coram.co.uk

PENTAGON SHOWER ENCLOSURE

To the installer: Please read these instructions carefully and leave with the home owner

for future reference. Incorrect fitting will invalidate the guarantee.

SAFETY

● Handle glass with great care. Although the glass is very tough, sharp impacts can damage both the

glass and metal frame.

● Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.

● Wear safety goggles, shoes and appropriate clothing.

● If you have long hair, tie it back out of the way.

BEFORE INSTALLATION

● This instruction leaflet must be used in conjunction with the instruction supplied with your shower

door. (A swing door shown in the example here).

● Check that the shower tray is level in all directions.The enclosure will not sit correctly on an uneven

surface. If uneven, the wall channels may not fit and the doors may not shut correctly.

● The enclosure should be fitted on tiled walls which are sealed with waterproof grout.

● There must be a good silicone seal between the rim of the shower tray and the wall.

13mm

● The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure

to the shower tray will result in water leaks.

Equipment needed:

Drill, 6.5mm masonry bit, 4.5mm & 3mm metal bits (general), Crosshead Screwdriver, Spirit Level,

Pencil, Silicone Sealant, Tape Measure, Masking Tape.

Note:

The screws and wall plugs supplied are for masonry walls.

For lightweight walls i.e. stud partition, plasterboard etc, use the correct type

of fixings.

Check contents of pack before installation.

If there is anything missing, contact our

Customer Careline for assistance, rather than

your supplier

CUSTOMER CARELINE: 01746 713410

PN3230

Wall Plug

PN9202

Screw

25mm

PN9203

Screw

13mm

PN8212

Washer

CUSTOMER CARELINE 01746 713410

PN40065

Wall Channel

Cover

PN10159

Extension

PN50145

Bracket

Moulding

PN50146

PN10745

Bracket

Corner

Moulding

Post

(CUP) PREM 00 71128 00 / Issue 4/ 10

PN40065

Wall Channel

Cover

PN10745

Corner

Post