HIKOKI CV 18DBL Instrukcja obsługi Instrukcja obsługi - Strona 7
Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Elektronarzędzie HIKOKI CV 18DBL. HIKOKI CV 18DBL 16 stron. Cordless multi tool
Również dla HIKOKI CV 18DBL: Instrukcja obsługi Instrukcja obsługi (16 strony)
Drukuj stronę
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of UC18YFSL charger lights for 1 second,
does not light for 0.5 seconds (off for 0.5 seconds), or
the charge indicator lamp of UC18YSL3 charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for 0.3
seconds). In such a case, fi rst let the battery cool, then
start charging.
○ When the pilot lamp or charge indicator lamp fl ickers (at
0.2-second intervals), check for and take out any foreign
objects in the charger's battery connector. If there are no
foreign objects, it is probable that the battery or charger
is malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about 3 seconds to
confi rm that the battery being charged with charger is taken
out, wait for a minimum of 3 seconds before reinserting it
to continue charging. If the battery is reinserted within 3
seconds, the battery may not be properly charged.
○ If the pilot lamp or charge indicator lamp does not blink
in red (every second) even though the charger cord is
connected to the power, it indicates that the protection
circuit of the charger may be activated.
Remove the cord from the power and then connect
it again after 30 seconds or so. If this does not cause
the pilot lamp or charge indicator lamp to blink in red
(every second), please take the charger to the HiKOKI
Authorized Service Center.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Remaining battery indicator
How to use the LED light
Mounting the application tool
Switch Operation
Adjusting operating speed
Sawing
Sanding
Charging a USB device from an
electrical outlet
Charging a USB device and battery
from an electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*2
Figure
1
2
3
4
5
6
7
*1
8
9
11-a
11-b
12
13
―
The tool is equipped with two modes: "Standard Mode" and
"AUTO Mode".
(1) Standard Mode
You can change the vibration frequency between 6000
to 20000 /min by adjusting the dial from "1" to "5".
(2) AUTO Mode
Depending on the workload, AUTO Mode "A" will
automatically change the vibration frequency to 15000
/min or 20000 /min. This has the eff ect of lowering
vibration and noise prior to and during operation.
Adjust the dial for the mode and speed that best suits your
task conditions and materials.
*1 Operating speed
Mode
Standard Mode
AUTO Mode
With AUTO Mode, the vibration frequency may not reach
20000 /min or return to 15000 /min depending on variables
such as the type of work or the attachment in use.
*2 Select accessories that are suited to a specifi c task.
For details contact HiKOKI Authorized Service Center.
MAINTENANCE AND INSPECTION
1. Inspecting the application tool
Continued use of a dull or damaged application tool
will result in reduced cutting effi ciency and may cause
overloading of the motor. Replace the application tool
with a new one as soon as excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
Page
NOTE
10
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
10
charged before storing them.
10
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
10
signifi cantly reducing battery usage time or rendering
11
the batteries incapable of holding a charge.
12
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
12
batteries two to fi ve times.
12
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
12
and purchase new batteries.
13
CAUTION
13
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
13
country must be observed.
13
14
7
Dial
Vibration Frequency
1 – 5
6000 – 20000 /min
No load: 15000 /min
A
With load: 20000 /min