HIKOKI H 3641DA Instrukcja obsługi Instrukcja obsługi - Strona 11

Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Elektronarzędzie HIKOKI H 3641DA. HIKOKI H 3641DA 20 stron.

Drukuj stronę

Disconnect the battery

Warning

Prohibited action

*1 Depending on attached battery. The heaviest weight is

measured with BSL36B18X.

Battery

Lights ;

The battery remaining power is over 75%.

Lights ;

The battery remaining power is 50%–75%.

Lights ;

The battery remaining power is 25%–50%.

Lights ;

The battery remaining power is less than 25%.

Blinks ;

The battery remaining power is nearly empty.

Recharge the battery soonest possible.

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow it to

fully cool down.

Blinks ;

Output suspended due to failure or malfunction.

The problem may be the battery so please

contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains

the accessories listed on page 15.

Standard accessories are subject to change without notice.

APPLICATIONS

Demolishing concrete, chiseling off concrete, grooving, bar

cutting.

Application examples:

Installation of piping and wiring, sanitary facility installation,

machinery installation, water supply and drainage work,

interior jobs, harbor facilities and other civil engineering

works.

SPECIFICATIONS

The specifications of this machine are listed in the Table on

page 15.

NOTE

○ Existing batteries (BSL3660/3626X/3626/3625/3620,

BSL18xx and BSL14xx series) cannot be used with this

tool.

○ Due to HiKOKI's continuing program of research and

development, the specifications herein are subject to

change without prior notice.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger's power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the charge indicator lamp will blink in red.

(See Table 1)

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 3 (on page 2).

3. Charging

When inserting a battery in the charger, charging will

commence and the charge indicator lamp will blink in

blue.

When the battery becomes fully recharged, the charge

indicator lamp will light up in green. (See Table 1)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be as

shown in Table 1, according to the condition of the

charger or the rechargeable battery.

Table 1: Indications of the charge indicator lamp

ON/OFF at 0.5 sec. intervals

(RED)

Lights for 0.5 sec. at intervals of

1 sec. (BLUE)

Lights for 1 sec. at intervals of

0.5 sec. (BLUE)

Lights continuously (BLUE)

Lights continuously (Continuous

buzzer sound: about 6 sec.)

(GREEN)

ON/OFF at 0.3 sec. intervals

(RED)

ON/OFF at 0.1 sec. intervals

(Intermittent buzzer sound:

about 2 sec.) (PURPLE)

NOTE

*1 If the red lamp continues to blink even after the charger

has been attached, check to confirm that the battery

has been fully inserted.

*2 Battery overheated. Unable to charge.

Although charging will start once the battery has cooled

down even when left in situ, the best practice is to

remove the battery and allow it to cool down in a

shaded, well-ventilated location before charging.

*3 Malfunction in the battery or the charger

–

Fully insert the battery.

–

Check to confirm that no foreign matter is stuck to

the battery mount or terminals. If there are no

foreign objects, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

Before charging *

Charged at less than

50%

Charged at less than

80%

Charged at more

than 80%

Charging complete

Overheat standby *

Charging impossible