HIKOKI M 18DYA Instrukcja obsługi Instrukcja obsługi - Strona 7
Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Elektronarzędzie HIKOKI M 18DYA. HIKOKI M 18DYA 16 stron.
Drukuj stronę
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
b) Use
power
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modifi ed.
Damaged
or
unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or
excessive temperature.
Exposure to fi re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside
the specifi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
CORDLESS CUT-OUT TOOL SAFETY
WARNINGS
1. Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
2. Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
tools
only
with
specifi cally
modifi ed
batteries
may
ADDITIONAL SAFETY WARNINGS
1. Preparing and checking the work environment. Make
sure that the work site meets all the conditions laid forth
in the precautions.
2. Before starting work, ensure that there are no buried
objects such as electrical conduits, water pipes, or gas
pipes in the work area.
If there is a buried object, the bit may touch it, resulting in
electric shock, leakage of electricity, or leakage of gas,
which may cause an accident.
3. Make sure there are no obstructions under the material
to be cut.
A strong repulsive force may occur, causing injury.
4. Use bits of the correct shank diameter suitable for the
speed of the tool.
5. Handle the bits very carefully.
6. Check the bit carefully for cracks or damage before
operation. Replace cracked or damaged bit immediately.
7. Avoid cutting nails. Inspect for and remove all nails from
the workpiece before operation.
8. Make sure to securely hold the tool during operation.
Failure to do so can result in accidents or injuries.
(Fig. 2)
9. Always switch off and wait for the bit to come to a
exhibit
complete stop before removing the tool from workpiece.
10. After changing the bits or making any adjustments, make
sure the collet nut and any other adjustment device are
securely tightened.
Loose adjustment device can unexpectedly shift,
causing loss of control, loose rotating components will
be violently thrown.
11. Never touch moving parts.
Never place your hands, fi ngers or other body parts near
the tool's moving parts.
12. Do not perform any operation using your hands to
support or guide the workpiece.
13. Always use with the depth guide securely attached to the
tool and positioned fl at and fi rmly against the workpiece.
14. Do not use this tool for drilling.
15. NEVER leave tool running unattended. Turn power off .
Don't leave tool until it comes to a complete stop.
16. The bit and shaft, collet nut, collet are very hot
immediately after operation. Avoid bare hand contact
with the bit for any reason.
17. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous work
may cause the temperature of the unit to rise, activating
the temperature protection circuit and automatically
stopping operation. If this happens, allow the power tool
to cool before resuming use.
18. Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
When electing to carry the tool hooked to your hip belt,
make sure to detach the tool bit. Failure to do so may
result in unexpected injury.
19. Do not look directly into the light. Such actions could
result in eye injury.
Wipe off any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
20. Always charge the battery at a temperature of 0°C–40°C.
A temperature of less than 0°C will result in over charging
which is dangerous. The battery cannot be charged at a
temperature higher than 40°C.
The most suitable temperature for charging is that of
20°C–25°C.
21. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
7
English