HIKOKI SB3608DA Instrukcja obsługi Instrukcja obsługi - Strona 13
Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Elektronarzędzie HIKOKI SB3608DA. HIKOKI SB3608DA 20 stron.
Drukuj stronęHow to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action
Removing and inserting the battery*
Charging
Installing the sanding belt*
How to use the dust bag*
How to use the elbow*
4
Switch operation
About the mode change function*
How to adjust sanding belt position*
How to hold and move the belt
sander*
7
How to work on corner
Remaining battery indicator
Charging a USB device from an
electrical outlet
Charging a USB device and battery
from an electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*1 Removing and inserting the battery
CAUTION
Before installing or removing the battery, turn the switch
to the OFF position.
If the battery is inserted with the switch in the ON
position, the motor will operate unexpectedly.
Figure
2
1
3
4
2
5
3
6
7
8
5
9
6
10
11
12
15-a
15-b
16
17
―
*2 Installing the sanding belt
Align the arrow on the inside of the sanding belt with the
direction of the mark on the tool and install it.
CAUTION
○ Use only sanding belt size specifi ed on the product
nameplate.
○ Sanding belt installed in the wrong direction will lower
work effi ciency and shorten life of sanding belt.
○ Avoid pinching your fi ngers when opening and closing
the lever.
NOTE
○ The drive pulley and idle pulley will be hot after use.
○ Use an air blow gun or similar device to remove any
debris from around the pulleys with the sanding belt
removed.
*3 How to use the dust bag
WARNING
Clean the dust bag before and after sanding metal, and
remove any sanding dust from inside. Metal sanding
dust can cause fi res.
*4 How to use the elbow
Adjust the angle of the elbow so that the dust is
discharged away from your body.
*5 About the mode change function
The unit has "Transmission mode" and "Auto mode".
○ With Transmission mode, the belt sander's number of
revolutions can be set at one of fi ve stages.
When operating in Transmission mode, the set number
of revolutions will be maintained regardless of changes
in load.
○ With Auto mode, you can lower noise and vibration by
lowering the maximum number of revolutions while in a
no-load state.
While in Auto mode, the number of revolutions will be
Page
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will be
2
lowered if the load decreases during operation. (Table 3)
2
○ Set the mode and dial according to work application.
3
3
Dial setting
3
1
4
2
4
3
4
4
4
5
4
A
5
*6 How to adjust sanding belt position
5
WARNING
○ If the sanding belt is positioned too close to the inside, it
5
may come into contact with the guard, producing sparks.
○ Do not peer inside between the sanding belt and
6
housing. Doing so risks dust or other debris entering
your eyes.
NOTE
6
○ If sanding belt moves during operation, adjustment can
be made while in operation.
16
○ Setting the dial to low speed (e.g., mode 1) makes it
easier to adjust.
○ If the sanding belt is positioned too close to the inside, it
may come into contact with the guard, causing the belt to
tear.
13
Table 3
Belt speed
122 m/min
220 m/min
310 m/min
400 m/min
450 m/min
122 m/min (No load)
450 m/min (With load)