HIKOKI G 10VE2 Instrukcja obsługi Instrukcja obsługi - Strona 9
Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Szlifierka HIKOKI G 10VE2. HIKOKI G 10VE2 20 stron.
Drukuj stronę4. Ensure that the depressed center wheel to be utilized is
the correct type and free of cracks or surface defects.
Also ensure that the depressed center wheel is properly
mounted and the wheel nut is securely tightened.
5. Confi rm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on.
6. To prolong the life of the machine and ensure a fi rst
class fi nish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is suffi cient
for eff ective grinding. Too much pressure will result in
reduced rotational speed, inferior surface fi nish, and
overloading which could reduce the life of the machine.
7. The wheel continues to rotate after the tool is switched
off .
After switching off the machine, do not put it down until
the depressed center wheel has come to a complete
stop. Apart from avoiding serious accidents, this
precaution will reduce the amount of dust and swarf
sucked into the machine.
8. When the machine is not use, the power source should
be disconnected.
9. Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident
before the depressed center wheel is assembling and
disassembling.
10. When using the tool at any value except the full speed
(Dial scale 6), the motor cannot be suffi ciently cooled
due to the decreased number of revolution. This could
result in the risk of burning and damaging the motor
before an overload protective mechanism starts to
function.
Make sure that you use the tool by lightly applying it
to the surface of material when you use it at any value
except the full speed (Dial scale 6).
11. Caution when using near welding equipment
When using the grinder in the immediate vicinity of
welding equipment, the rotational speed may become
unstable. Do not use the grinder near welding equipment.
12. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
13. Do not operate from a direct current power source,
booster or any other type of transformer. Doing so may
not only cause damage to the grinder, but may lead to
accidents.
14. Some mobile generators may not be usable with the
machine.
NAMES OF PARTS (Fig. 1–Fig. 11)
Push button
Side handle
Gear cover
Depressed center
wheel
M5 screw
Wheel guard
Switch
Motor
Filter
Tail cover
Housing
Nameplate
Dial
Tool-less wheel guard
Lever
Bump
Notch
Wheel washer
Wheel nut
Wrench
9
Cutting wheel
(sold separately)
Guard clip
(sold separately)
Diamond wheel
(sold separately)
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
G10VE2 / G13VE2: Disc Grinder
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
V
Rated voltage
Alternating current
n
Rated speed
/min
Revolution or reciprocations per minute
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Lock
Unlock
Warning
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Wrench .........................................................................1
○ Depressed center wheel ...............................................1
○ Side handle ...................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Grinding of synthetic resins, slate, brick, marble, etc.
○ Cutting of synthetic concrete, stone, brick, marble, and
similar materials.
English
Mesh
Soft brush
With side guard
(sold separately)