Gree Multi21 CONS18HP230V1AF Instrukcja obsługi - Strona 13
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Klimatyzator Gree Multi21 CONS18HP230V1AF. Gree Multi21 CONS18HP230V1AF 18 stron.
Drukuj stronę
OPERATION OF REMOTE CONTROLLER (Continued)
OPERATION OF REMOTE CONTROLLER (Continued)
Function introduction for combination
buttons
Energy-saving function
Under COOL mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off energy-saving
function. When energy-saving function is started up,
"SE" will be shown on remote controller, and the unit
will adjust the set temperature automatically, to the
factory setting, to achieve maximum energy savings.
Press "TEMP" and "CLOCK" buttons simultaneously
again to exit energy-saving function.
NOTE
• Under energy-saving function, fan speed defaults to
Auto and can't be adjusted.
• Under energy-saving function, you cannot adjust
Fan speed or use TURBO.
• If the energy-saving function has been set in the
COOL mode, pressing the "SLEEP" button will
cancel energy-saving. If the SLEEP function has
been set in the COOL mode, starting the energy-
saving function will cancel SLEEP.
Vacation mode (freeze guard) Heating in 8°C mode
or 46°F mode
In the HEAT mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off this heating
function. When this function is started up, " " and
"46°F (8°C)" will be shown on remote controller, and
the space will not fall below 46°F (8°C). Press "TEMP"
and "CLOCK" buttons simultaneously again to exit "46°F
(8°C)" heating function.
NOTE
• Under 46°F (8°C) heating function, fan speed is
defaulted at auto speed and it can't be adjusted.
• Under 46°F (8°C) heating function neither the
temperature nor the fan speed can be adjusted.
"TURBO" will not work either.
• Sleep function and 46°F (8°C) heating function
can't operate at the same time. If 46°F (8°C) heating
function has been set under heat mode, pressing
the "SLEEP" button will cancel 46°F (8°C) heating
function. If sleep function has been set under heat
mode, initiating the 46°F (8°C) heating function will
cancel SLEEP function.
MI NI -F LOO R CO NS OLE A S ER IESOWNERS M A NUAL - INDOOR UNIT
Remote lock-out
Press " " or " " simultaneously to turn on or turn
off Remote lock-out. When Remote lock-out is on,
" " icon is displayed on remote controller. If you operate
the remote controller, the " " icon will blink three times
without sending signal to the unit.
Temperature display switchover function
Under OFF status, press " " and "MODE" buttons
simultaneously to switch temperature display between
°C and °F.
Replacing batteries in remote controller
Fig 1
Lift the cover along the direction of arrow (as shown
1.
in Fig 1 ).
Take out the original batteries (as shown in Fig 1 ).
2.
Place two (AAA 1.5V) dry batteries, and make sure
3.
the position of " + " polar and " – " polar is correct (as
shown in Fig 2 ).
Reinstall the cover (as shown in Fig 2 ).
4.
NOTICE
• During operation, point the remote control signal
sender at the receiving window on indoor unit.
• The distance between signal sender and receiving
window should be no more than 26 ft and there
should be no obstacles between them.
• Other electronics may interfere with the remote
signal, remote controller should be close to indoor
unit during operation.
• Replace batteries with an equivalent model when
replacement is required.
• When you don't use remote controller for a long
time, take out the batteries.
• If the display on remote controller is fuzzy or there's
no display, replace batteries.
Fig 2
| 1 3