HIKOKI G18DBAL Instrukcja obsługi Instrukcja obsługi - Strona 10
Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Szlifierka HIKOKI G18DBAL. HIKOKI G18DBAL 20 stron.
Drukuj stronę
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Remaining battery indicator
(Main Body)
Remaining battery indicator
(Battery: BSL36A18)
Fitting and adjusting the wheel
guard
Fixing the side handle
Assembling depressed center wheel
Assembling cutting wheel
Switch operation
Switching operation modes
Grinding angle and grinding method
Detaching the fi lter
Charging a USB device from an
electrical outlet
Charging a USB device and battery
from an electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
About the Mode Change Function
With the storage battery installed to the main unit and the
unit switched on, pressing the Mode Change switch will
switch the operation mode to auto mode. While in Auto
Mode, the Auto Mode display lamp will remain lit.
○ With Auto Mode, you can lower noise and vibration by
lowering the maximum number of revolutions while in a
no-load state.
While in Auto Mode, the number of revolutions will be
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will be
lowered if the load decreases during operation.
MAINTENANCE AND INSPECTION
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
Figure
Page
1
12
6. Cleaning the fi lter (Fig. 11)
2
12
3
12
NOTE
○ To clear the unit of grime or dust, periodically run
4
12
5
12
○ After cleaning, make sure to securely attach the fi lter.
6
13
7. Storage
7
13
8
13
9
13
NOTE
10
14
11
14
12
14
13-a
15
13-b
15
14
15
15
15
―
16
CAUTION
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
parts).
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
10
When the cordless disc grinder is stained, wipe with a
soft dry cloth or a cloth moistened with soapy water. Do
not use chloric solvents, gasoline or paint thinner, for
they melt plastics.
After use, detach the fi lter and remove any grime or dust
from the screen with an airgun or other tool.
the motor in a no-load state and blow dry air into the
ventilation hole with the fi lter removed.
Accumulation of grime or dust accumulates in the motor
can cause damage.
Store the cordless disc grinder in a place in which the
temperature is less than 40°C, and out of reach of
children.
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.