HIKOKI WR36DH Instrukcja obsługi Instrukcja obsługi - Strona 11

Przeglądaj online lub pobierz pdf Instrukcja obsługi Instrukcja obsługi dla Sterownik udarowy HIKOKI WR36DH. HIKOKI WR36DH 20 stron.

Drukuj stronę

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger's power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the charge indicator lamp will blink in red.

(See Table 1)

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 4 (on page 2).

3. Charging

When inserting a battery in the charger, charging will

commence and the charge indicator lamp will blink in

blue.

When the battery becomes fully recharged, the charge

indicator lamp will light up in green. (See Table 1)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be as

shown in Table 1, according to the condition of the

charger or the rechargeable battery.

Table 1: Indications of the charge indicator lamp

ON/OFF at 0.5 sec. intervals

(RED)

Lights for 0.5 sec. at intervals of

1 sec. (BLUE)

Lights for 1 sec. at intervals of

0.5 sec. (BLUE)

Lights continuously (BLUE)

Lights continuously (Continuous

buzzer sound: about 6 sec.)

(GREEN)

ON/OFF at 0.3 sec. intervals

(RED)

ON/OFF at 0.1 sec. intervals

(Intermittent buzzer sound:

about 2 sec.) (PURPLE)

NOTE

*1 If the red lamp continues to blink even after the charger

has been attached, check to confirm that the battery

has been fully inserted.

*2 Battery overheated. Unable to charge.

Although charging will start once the battery has cooled

down even when left in situ, the best practice is to

remove the battery and allow it to cool down in a

shaded, well-ventilated location before charging.

*3 Malfunction in the battery or the charger

–

Fully insert the battery.

–

Check to confirm that no foreign matter is stuck to

the battery mount or terminals. If there are no

foreign objects, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

Before charging *

Charged at less than

50%

Charged at less than

80%

Charged at more

than 80%

Charging complete

Overheat standby *

Charging impossible

○ When the battery charger has been continuously used,

the battery charger will be heated, thus constituting the

cause of the failures. Once the charging has been

completed, give 5 minutes rest until the next charging.

(2) Regarding the temperatures and charging time of the

battery (See Table 2)

Model

Type of battery

Charging voltage

Temperatures at which the

battery can be recharged

1.5 Ah

2.0 Ah

2.5 Ah

Charging time for

3.0 Ah

battery capacity,

approx. (At 20°C)

4.0 Ah

5.0 Ah

6.0 Ah

1.5 Ah

(× 2 unit)

Charging time for

multi volt battery

2.5 Ah

capacity, approx.

(× 2 unit)

(At 20°C)

4.0 Ah

(× 2 unit)

Number of battery cells

Charging voltage for USB

Charging current for USB

Weight

NOTE

○ The recharging time may vary according to the ambient

temperature and power source voltage.

○ If charging takes a long time

–

Charging will take longer at extremely low ambient

temperatures. Charge the battery in a warm location

(such as indoors).

–

Do not block the air vent. Otherwise the interior will

overheat, reducing the charger's performance.

–

If the cooling fan is not operating, contact a HiKOKI

Authorized Service Center for repairs.

4. Disconnect the charger's power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

1. Connect the charger's power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the pilot lamp will blink in red. (See Table 3)

Table 2

UC18YSL3

Li-ion

14.4–18 V

0°C–50°C

15 min

20 min

25 min

20 min

(BSL1430C, BSL1830C:

30 min)

26 min

(BSL1840M: 40 min)

32 min

38 min

20 min

32 min

52 min

4–10

5 V

2 A

0.6 kg