GameChanger Audio BIGSBY Skrócona instrukcja obsługi - Strona 7
Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Pedał muzyczny GameChanger Audio BIGSBY. GameChanger Audio BIGSBY 8 stron.
Drukuj stronęSAVING AND RECALLING MIDI PRESETS
The BIGSBY Pedal offers 10 preset slots accessible through MIDI PC Messages.
These preset slots can be used to save the pedal's knob settings as well as the EXP Out settings
and the MIDI Sync status.
You can find the full PC and CC message chart on a separate index card included in the BIGSBY
Pedal's package, but the first 21 PC slots are dedicated to saving and recalling 10 PRESET slots.
PC messages 1-10 are used to recall presets 1-10 and PC Messages 11-20 will save the pedal's
current settings to slots 1-10 accordingly.
Example:
Dial in your desired settings using the front panel knobs -
to save these settings to Slot 1 - send the PC message 11;
to save these settings to Slot 2 - send the PC message 12, etc.;
to save on Slot 10 - send the PC message 20.
To recall any of the presets 1-10 send the according PC messages 1-10.
When in a preset - use the PC message 21 to recall the physical values of the knobs.
RECALIBRATING THE BIGSBY PEDAL
The BIGSBY Pedal uses a system of optical sensors to ensure precise tracking of the foot-pedal's
movements. To maintain precision over time the BIGSBY automatically calibrates itself on every
power-up, in order to confirm the foot-pedal's "zero" or "center" position, therefore:
When powering up the BIGSBY Pedal make sure that the foot-pedal IS NOT pressed down.
If the foot-pedal is pressed down during the BIGSBY's power-up the pedal will detect an error and
switch into RECALIBRATION MODE, indicated by flashing white&red knobs.
When the pedal is in RECALIBRATION mode, please perform the following steps:
1) Restart the BIGSBY Pedal by removing the power supply and plugging it back in.
Make sure that there is no pressure applied to BIGSBY's foot-pedal, while restarting.
2) Press the BIGSBY's foot-pedal all the way down and then all the way up.
This will complete the RECALIBRATION process and the BIGSBY Pedal will return into performance
mode.
In some cases when only a small amount of pressure was applied to the pedal during power-up,
the calibration error will be undetected, but you will still hear that the dry signal is slightly pitched.
In this case - make sure that no pressure is applied to the foot-pedal and restart the BIGSBY Pedal.
TECHNICAL SPECIFICATIONS
Connector type In:
Input impedance:
Max input level:
Connector type Out:
Output impedance:
Max output level:
Connector type Exp:
Input impedance (ring):
Output impedance (tip):
Max input level:
Max output level:
Connector MIDI:
Type:
Frequency response:
Signal to noise ratio:
Operating temperature:
Connector type power supply:
Input voltage:
Input current:
Power consumption:
Dimensions (LxWxH):
Weight:
1/4" Unbalanced TS
1 MΩ
9 dBu
1/4" Unbalanced TS
100 Ω
9 dBu
1/4" Unbalanced TRS (Exp out) / 1/4" Unbalanced TS (FSW in)
100 kΩ
220 Ω
20 dBu
20 dBu
3.5 mm TRS (mini jack), Type-B
Optically isolated input, RF filtered
20 Hz to 20 kHz (±1 dB)
90 dB (A weighted)
0º to 50º C
9V DC, center negative 2.1 x 5.5 mm plug
9V DC
220 mA
2 W
220 x 110 x 86 mm / 8,6 x 4.3 x 3.3 in
960 g / 2.11 lb
7