IKEA ENHET Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Wyposażenie wnętrz IKEA ENHET. IKEA ENHET 10 stron. Kitchen
Również dla IKEA ENHET: Instrukcja instalacji (16 strony), Instrukcja instalacji (20 strony)

Drukuj stronę

Installing the base cabinets/frames

Once you are done with the installation of the wall

cabinets you move on to the base cabinets. Again,

start from the corner of the room and place the cabi-

net on the supporting wooden strip. If you build a line

kitchen, make sure you leave some space between the

wall and the cabinet to a allow for doors or drawers to

open properly.

If you build a corner base solution with a 40 cm door,

Make sure that the corner panel and the front edge

place the cabinet 268 mm from the wall (A). If you

of the adjacent cabinet align.

build it with a 60 cm door, place the cabinet 468 mm

from the wall (A). In both cases, the adjacent cabinet

is placed 688 mm from the wall (B).

As you proceed with the next cabinet, level and align

When you reach the place where you want your

the two cabinets by using a clamp. Use the screws

sink and tap, use the designated ENHET cabinet

provided to attach the adjacent cabinets.

for sink, which has a construction that allows for

pipes coming from either the wall or the floor. See

assembly instructions for how to build the different

configurations.

To install a cabinet after the dishwasher niche, make

When you install an open base frame, you don't use

sure the spirit level reaches both cabinets at the

a supporting strip. Instead, align the top of the open

front and at the back of the cabinets. Make sure the

frame with the top of the adjacent cabinet before

distance at the front and back of the niche remains

you fix the frame to the wall.

60 cm. Once you have the correct alignment, secure

the cabinet to the wall.

If you have a corner kitchen, you build the corner base

solution with a 80 cm base cabinet in combination with

the ENHET corner panel. For this solution, follow the

assembly instruction included with the ENHET corner

panel.

Note: ENHET open frames can't be used under a sink,

built-in hob or for a built-in oven.

Fix the cabinet using the appropriate type and

length of screw. (Throughout the installation process

you may need to loosen the screws a bit in order

to make smaller adjustments when aligning the

cabinets and frames.)

The dishwasher, normally placed next to the sink

cabinet, stands on its own base so here there is no

need for a supporting strip. Leave a 60 cm wide gap

between the sink cabinet and the next cabinet.

Once all your base cabinets are installed, check that

they are level and that you are happy with the result,

before securing them by tightening the screws a

final time.

Installing the worktop

With your cabinets in place, it's time to install your

worktop. Before you start, be sure to read the worktop

assembly instruction to learn about the things you

need to consider as you prepare and install it. When

cutting the worktop to fit it with your kitchen, keep in

mind that you are you are handling rather thick and

heavy material so make sure you have the proper work

Start by placing the worktop on top of the base

Use a circular saw and G clamps to keep a straight

cabinets and push it against the wall.

line as you cut the worktop. To avoid splinter, cut

Once in position, measure the worktop from the side

with the worktop underside facing up when using a

edge of the cabinet underneath. With the addition

buzz or jig saw, but with the top facing up if using a

of at least a 1.5 cm overhang, make a mark on the

handsaw. A tip is to have a second person hold the

worktop.

piece to be cut off to avoid the edge from splintering.

For a sink cut-out, you start by tracing the inner

Place the worktop upside down, then place the

boundaries of the sink cabinet on the underside of

sink upside down within the previously marked

the positioned worktop.

boundaries/lines, making sure there is equal space

all around. Trace the outline of the sink.

Use a jigsaw to cut out the space for your sink. It's

For the hob cut-out, locate the mid point of the

helpful to drill a hole on the inside corners of your

hob cabinet. See the hob installation guide for the

outline before cutting. These holes, big enough to

cut-out dimensions and the minimum distances to

fit the jigsaw blade, serve as the entry point for the

pay attention to.

jigsaw and enables you to make a cleaner cut.

Make sure that the cut-out perimeter doesn't collide

with the top rail of the cabinet.

space and tools. It's helpful to use a pair of sawhorses

to setup a cutting station. Here, you can benefit from

having a second person available, to help you carry

and hold the worktop while you perform the different

steps. If you need to customise your worktop for a sink

or hob, follow the assembly instruction of your sink or

hob.

After you have cut the worktop you need to seal the

cut raw edge. Open edges create a entry point for

humidity or water, which could cause swelling and

deterioration. Follow the assembly instruction of the

worktop to apply the edge band that comes with

each IKEA pre-cut worktop. If you do not have a lose

strip we recommend to seal the open edge using

silicone.

Then, follow the assembly instructrion of the sink to

mark the actual cutting line.

For last steps on installing the

worktop, see next page