Decibullz CUSTOM MOLDED TRUE WIRELESS EARPHONES Podręcznik - Strona 2

Przeglądaj online lub pobierz pdf Podręcznik dla Słuchawki Decibullz CUSTOM MOLDED TRUE WIRELESS EARPHONES. Decibullz CUSTOM MOLDED TRUE WIRELESS EARPHONES 2 stron. Custom molded true wireless earphones

Drukuj stronę

START HERE

For the best results, watch

our instructional video at

www.decibullz.com/truewireless

HOW TO MOLD

Please review these instructions ﬁrst to familiarize

yourself with the molding process.

YOU WILL NEED

A cup, bowl, or pan at least 4 inches deep with a ﬂat base

at least 3 inches in diameter and boiling water.

4in

-OR-

3in

STEP 1

Charge the case and earphones

Place the earphones into the charging case and fully charge earphones and

charging case before setting up. The left earphone will only charge in the

left cavity and vice versa. The "L" & "R" on the charging case will light up

while the earphones are charging. If the Custom Molded Earpieces are

attached to the earphones remove them at this time.

USB-C

CABLE

STEP 2

Select silicone tip size

Choose the silicone tips that will ﬁt you best and securely place them onto

the custom earpieces. Check to make sure the silicone tips are securely

attached. ONLY PLACE THE CUSTOM MOLDS AND THE MOLDING TOOL INTO

THE WATER. DO NOT PLACE EARPHONES INTO THE WATER!

STEP 3

Place custom molds on molding tool

Assemble molding tool as shown. Test the molding tool to

make sure it ﬁts into your container and sits ﬂat on the base.

Place custom molds on the molding tool making sure the left and

right earpieces are on the left and right side of the molding tool.

STEP 4

Heat water to a boil

Stovetop: Boil 3in of water and remove from heat source.

Kettle or Microwave: Fill a container with 3in of boiling water. Slowly insert

the molding tool and earpieces into the hot water and let sit for 5 minutes.

CAUTION:

WATER AND

OTHER ITEMS WILL

BE VERY HOT.

3in of Water.

STEP 5

Preparing to mold the earpieces

Carefully remove the molding tool and molds from the hot water and

remove one of the custom molds. Place the tool and remaining

earpiece back in the water. Wait 30 seconds for the earpiece, that you

have just removed from the molding tool, to cool.

TIP

Using a mirror can make the process easier.

Be sure the "R" custom mold goes in your right ear. The silicone tip should be

towards the bottom. Now ﬁrmly press the earpiece into your ear. You may need to

press and smooth the molding material slightly for a cleaner appearance.

Immediately repeat the process for the other ear with the remaining mold. Leave

the earpieces in your ear for 4 minutes to cool. Repeat the process for the other ear.

CAUTION:

THE MOLD INTO EAR WHILE IT

IS HOT! WAIT UNTIL THE

MOLD IS WARM AND PLIABLE.

Note: You will not feel an acoustic seal until the

Once the earpieces have cooled for 4 minutes, remove them from your

ears and snap in the earphones. Make sure the right earphone goes

into the right earpiece and the left earphone goes into the left earpiece.

Place both earphones back into the charging case and

follow pairing and use instructions on the next page.

The top of the molding

tool should remain

above the water for

safe removal.

If you do not feel an acoustic seal after molding try various sizes and

combinations of canal tips before re-molding. If for any reason you would

like to re-shape your earpieces simply unsnap the earphones from the

custom molds by using the notches to gently release the earphones.

To separate the custom mold from the earphone, place your thumb and

ﬁnger on the notches at the top and bottom of the earphone and gently pull.

STEP 6

Molding the earpieces

DO NOT PLACE

earphones are inserted in the next step.

STEP 7

Snap in the earphones

REMOLDING

Then repeat steps 2-6.