KitchenAid Architect Series II KFGU706VSS Wymiary

Przeglądaj online lub pobierz pdf Wymiary dla Płyta grzewcza KitchenAid Architect Series II KFGU706VSS. KitchenAid Architect Series II KFGU706VSS 1 stron. 30" (76.2 cm) and 36" (91.4 cm) gas built-in cooktop
Również dla KitchenAid Architect Series II KFGU706VSS: Instrukcja instalacji (20 strony), Podręcznik wymiarów (1 strony)

Drukuj stronę

PRODUCT MODEL NUMBERS

KFGS306V

KFGS366V

Gas Supply: This cooktop is factory set for use with

natural gas. Cooktop can be converted to LP gas.

Conversion must be done by a qualified service

technician. Provide a gas supply line of 3/4" (1.9 cm)

rigid pipe to the cooktop location. A smaller size pipe on

longer runs may result in insufficient gas supply. Pipe-

joint compounds that resist the action of LP gas must be

used. Do not use TEFLON

tape. With LP gas, piping or

tubing size can be 1/2" minimum. Usually, LP gas

suppliers determine the size and materials used in the

system.

No attempt shall be made to convert the cooktop from

the gas specified on the model/serial rating plate for use

with a different gas without consulting the serving gas

supplier. See the Gas Conversion instructions provided in

the package containing literature.

Electrical: A 120 volt, 60 Hz., AC only, 15-amp fused

electrical circuit is required. A time-delay fuse or circuit

breaker is also recommended. It is recommended that a

separate circuit serving only this cooktop be provided.

PRODUCT DIMENSIONS

A. 30

" (76.7 cm) on 30" (76.2 cm) models,

36 " (92.0 cm) on 36" (91.4 cm) models

B. 21" (53.3 cm)

C. 3" (7.6 cm)

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Gas Built-in Cooktop

KFGU706V

KFGU766V

INSTALLATION CLEARANCES

A. 30" (76.2 cm) on 30" (76.2 cm) models; 36" (91.4 cm) on 36" (91.4 cm) models

B. Combustible area above countertop (shown by dashed box above)

C. 30" (76.2 cm) minimum clearance between top of cooktop platform and bottom of

uncovered wood or metal cabinet (24" [61.0 cm] minimum clearance if bottom of

wood or metal cabinet is covered by not less than 1/4" [0.6 cm] flame retardant

millboard covered with not less than No. 28 MSG sheet steel, 0.015" [0.04 cm]

stainless steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper). If installing

a range hood see NOTES.*

D. 13" (33.0 cm) recommended upper cabinet depth

E. 1-1/8" (2.8 cm)

F. 20" (50.8 cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop within minimum

horizontal clearances to cooktop

H. Grounded outlet - Locate within 24" (61.0 cm) of right rear corner of cutout

I. 29" (73.7 cm) on 30" (76.2 cm) models; 35-1/4" (89.5 cm) on 36" (91.4 cm) models

J. 24" (61.0 cm) minimum countertop depth is required

K. 2-7/8" (7.3 cm) minimum distance to rear combustible surface

L. Gas line opening - Wall: anywhere 5" (12.7 cm) below underside of countertop.

Cabinet floor: anywhere within 6" (15.2 cm) of rear wall is recommended

M. 8" (20.3 cm) minimum distance to nearest left side combustible surface.**

N. 8" (20.3 cm) minimum distance to nearest right side combustible surface.**

30" (76.2 cm) Cooktop Overall: M + N must equal 48" (122.0 cm) minimum + 29"

(73.7 cm) cutout for cooktop or 77" (195.6 cm)

36" (91.4 cm) Cooktop Overall: M + N must equal 48" (122.0 cm) minimum + 35-1/4"

(89.5 cm) cutout for cooktop or 83-1/4" (211.5 cm)

**M + N combined must be at least 48" (122.0 cm) minimum overall

Example 1: M = 8" (20.3 cm) left side + N = 40" (101.6 cm) right side = 48" (122.0 cm)

Example 2: M = 24" (61.0 cm) left side + N = 24" (61.0 cm) right side = 48" (122.0 cm)

NOTES:

After making the countertop cutout, some installations may require notching down the

base cabinet side walls to clear the cooktop base. To avoid this modification, use a

base cabinet with sidewalls wider than the cutout.

If cabinet has a drawer, a 4" (10.2 cm) depth clearance from the countertop to the top

of the drawer (or other obstruction) in base cabinet is required. The drawer depth may

need to be shortened to avoid interfering with the regulator.

*If installing a hood above the range, follow the hood instructions for dimensional

clearances above the cooktop surface.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. 8286867B

06-25-08