Decko 24000-DKO Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Otwieracz drzwi garażowych Decko 24000-DKO. Decko 24000-DKO 14 stron. Handles doors 18 ft. wide & up to 7ft.tall

Drukuj stronę
Opener Assembly Parts
1
2
3
10
8
9
11
12
13
14
Item
Part No.
1
24935
2
*
3
*
4
*
5
24905
6
*
7
*
8
*
9
*
10
*
11
*
12
*
13
*
14
24937
24
* Should be replaced by qualified technician only
5
4
6
Limit System Assembly
7
Open limit Contact
Blue
Gear
Center limit Contact
Close limit Contact
Name / Description
Sprocket Cover
Sprocket and gear assembly
Chassis
Lamp plate
Lamp Dome
Capacitor
Capacitor holder
Motor assembly
RPM wheel
Logic Board holder
Logic Board
Limit system driving gear
Limit system assembly
Opener cover

Rail and Trolley Assembly

CAUTION
!
- DO NOT connect power until instructed.
- To prevent INJURY, keep hands and fingers
away from joints and possible sharp edges.
- Wear gloves when installing chain and cable.
Trolley direction (Top View)
Rail — Header Segment
Green
Screw
Cable Eyelet
3
Green
Clevis Pin
1
Orange
2
Red
Screw
4
Hitch Pin
Trolley Shaft
Hitch Pin
Connect shaft to Trolley with "click"
Trolley Shaft
Fig.3
Trolley Shaft
Loosely link together
Rail — End Segment (tapered)
with Trolley Stop Bolt
Rail — Middle Segments
(tapered) x 3
When connecting the rails ensure they are securely connected as shown above.
To apply additional force tap gently on the end of the rail with a rubber mallet*.
*Only use a soft rubber mallet to tap on the end of the rails as other tools may damage your rail.
To Assemble Rail and Opener
1.
Prepare the rails as shown in Fig.1.
2.
Connect the rails starting with the Header Segment. Insert
the tapered ends into open ends, apply any additional force
necessary by tapping the Rail on padded flooring. Ensure
the End Segment has Trolley Stop Bolt facing up. Make
sure the rails are securely joined together as shown.
3.
Slide the Trolley onto the rail from the Header Segment.
Pulley
Make sure the arrow is pointing towards the door as shown
in Fig.1.
Fig.2
4.
Connect the rail assembly to the Rail Bracket on the Open-
er.
To Assemble the Header Section of Rail
Follow steps shown in Fig.2:
1.
Remove the "Trolley Shaft and Cable" from the Chain carton
Clevis Pin — 3/8" x 1-3/4"
and lay it beside the rail assembly. Hold Cable Eyelet on the
end of cable and thread about 20" (50cm) through the slot
on the Header Segment of the rail.
2.
Insert the Pulley into the opening while the cable is hanging.
3.
Secure the Pulley by inserting the 3/8" x 1-3/4" Clevis Pin
through the top of the rail.
Trolley
4.
Lock the Clevis Pin with a Hitch Pin. Rotate the Pulley to
ensure it spins smoothly.
Refer to Fig.3 to connect the Trolley Shaft to the Trolley. Slide
both the Trolley Shaft and Trolley towards each other. A "click"
will be heard when they are connected.
Chain
To Link Cable with Chain
Chain-to-Cable Connector
Refer to Fig.4. Place the chain carton beside the rail, hold the
"Chain to Cable Connector" and pull about 8" (20cm) of chain
Fig.4
from the box. Thread the Chain to Cable Connector onto the
Trolley Shaft so that they are loosely linked together.
Fig.1
Rail Bracket
Opener
5