Decko 24000-DKO Instrukcja obsługi - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Otwieracz drzwi garażowych Decko 24000-DKO. Decko 24000-DKO 14 stron. Handles doors 18 ft. wide & up to 7ft.tall

Drukuj stronę
Operating the Opener
!
To Prevent SERIOUS INJURY or DEATH:
- READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS IN THE OWNER'S MANUAL AND LABELS
- Keep Transmitter and battery out of reach of children.
- NEVER permit children to access the Push Button or remote Transmitters.
- Operate the door ONLY when it is properly adjusted, and there are no obstructions and is in clear sight.
- ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door.
- If Travel limit adjustment is made, Force Adjustment may also needed.
- After ANY adjustments, the Safety Reverse Test MUST be performed to ensure the door reverses on contact
with a 1-1/2" thick object (2x4 laid flat).
- ALWAYS ensure that your door is balanced and in good working condition.
Emergency Release Knob
Activating the Opener
Controls
Momentray press the "DOOR" button on the Wall Panel, the door starts to move, and
controls as follows:
- Open or close the door.
Wall Panel (Indoor)
- Reverse the door while it is closing
- Stops the door while it is opening.
- Close the door when the Photo Eye Safety System is not installed, misaligned or
obstructed INTENTIONALLY.
Same functions* as the Push Button with remote distance up to 100ft. in open field.
Hand-Held Transmitter
*For safety concerns, the Hand-Held Transmitter WON'T work if the Photo Eye Safety
System is not properly installed and aligned.
Keyless Entry (Optional)
Program the Keyless Entry pad accordingly and access the door using the PIN code.
20
WARNING
Courtesy Light
Wall Panel
Photo Eye Safety System
Invisible Light Beam
Actual Operating Scenario
Operation

Mounting Opener to Ceiling

!
To prevent SERIOUS INJURY or DEATH:
- DO NOT connect power until instructed.
- Install the Opener at least 7 feet (2.13m) above the floor.
- Fasten the Opener SECURELY to STRUCTURAL SUPPORTS of the garage to prevent falling.
- If installing Brackets to masonry, concrete anchors (not provided) MUST be used.
Fig.1
Finished ceiling
Angle Iron not provided
Bolt / Lock Washer / Nut
not provided
Fig.2
Finished ceiling
Angle Iron not provided
Bolt / Lock Washer / Nut
not provided
Fig.3
WARNING
To Mount the Opener to Ceiling
The three most common installation options are shown in
Fig.1-3.
Fig.1 shows mounting the Opener directly to structural
support on the ceiling. Fig.2 and 3 show mounting on a
finished ceiling, with heavy duty angle iron*.
*(angle iron not included)
Determine the mounting option that works best for your
application and follow installation steps below:
1.
Raise the Opener and rail assembly and temporarily place it
on a stepladder.
2.
Position the Opener and rail assembly so that it is aligned to
the center line of the garage door. If the Header Bracket
was mounted off center, align the Opener with the Header
Bracket.
3.
Measure the distance from each side of the Opener to the
structural supports.
4.
Cut both Hanging Brackets to appropriate length.
5.
Drill 3/16" holes in the structural supports.
6.
Secure one end of each of the Hanging Brackets to the
structural supports using 5/16" x1/2" Lag Screws (provided).
7.
Secure the Opener to the Hanging Brackets and secure
each side with a 5/16" x 1" Bolt and Flange Nut (provided).
8.
Move the door manually to check clearance between
highest point of travel of the door and rail. If the door hits the
rail, raise the Header Bracket or adjust the mounting of
Opener.
9.
Remove the ladder ONLY when the Opener is securely
mounted to the structural supports.
Fastening Hanging Brackets to structural supports
Lag Screw 5/16" x 1-1/2"
Securing Opener to Hanging Brackets
Flange Nut
Bolt 5/16" x 1"
9