KitchenAid KEC Instrukcja instalacji - Strona 8
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Płyta grzewcza KitchenAid KEC. KitchenAid KEC 10 stron. Electric cooktop
Również dla KitchenAid KEC: Instrukcja instalacji (16 strony), Instrukcja instalacji (16 strony)
Drukuj stronę
For all cooktop
models
with four-
wire cable from the cooktop.
(:These cooktops
are
manufactured
with white
(neutra 0 power
suppJy wire and
a cabinet-connected
bare ground
wire factory-crimped
together.):
Where tocal codes Do Not permit
connecting
the frame-ground
conductor
to the neutra! (white}
junction box wire:
1, Disconnect
power supply.
2, Remove the junction box cover from
the junction box inside the cabinet.
3, Connect the flexible, armored cable
from the cooktop to the junction box
using a U.L =or C.S.A.qisted conduit
connector. Tighten screws on conduit
connector.
4, Connect the two black wires together
and the two red wires together.
5. Separate
the factory-crimped
bare and
white cooktop cable wires.
6, Connect the two white wires together
using twist-on
connectors.
7, Connect the bare ground wire from the
cooktop cable to a grounded
wire in
the junction
box or other grounded
connector
using twist-on connector.
(See Figure 3.)
Do Not connect
bare ground
wire to
neutral
(white)
wire in junction
box,
8. Replace the junction
box cover.
Check operation
Turn on electrical supply.
71
Check that cooktop surface elements
heat and indicator lights are operating correctly.
8B
Checkthat downdraftvent operates,if
the cooktop does not operate,disconnect the
power supply and checkthat wire connections
have been madecorrectly.
You have just finished
installing
your
new downdraft
cooktop. To get the
most efficient
use from your new
cooktop,
read your Use & Care Guide.
Keep Installation instructions and
Guide close to cooktop
for easy
reference.
Ceektep remevam
tf removing the cooktop is necessary
for cJeaning or maintenance:
1. Disconnect electrical supply.
2. Disconnect vent system.
3. Lift cooktop out of countertop to
complete cleaning or maintenance.
After cJeaning and maintenance:
1. Reinstall cooktop in cutout.
2. Check that front edge of cooktop is
parallel to front edge of countertop.
3. Connect vent system.
4. Connect electrical supply.
If ceektep
net eperate:
[_
Check that the circuit breaker is not
tripped or the house fuse blown.
[_
Check that the power supply cord is
plugged into the outlet (120 V models).
[_See
Use and Care Guide for
troubleshooting list.
Note: Refer to Use and Care Guide for
operating and cleaning instructions.
If you need
if you have questions
about
operating,
cJeaning or maintaining
your cooktop:
[_
Refer to Use and Care Guide,
[_
Call the Customer Interaction Center.
Check your Use and Care Guide for
a toll-free number to call or call the
dealer from whom you purchased
this appliance. The dealer is listed in
the Yellow Pages of your phone
directory under "Appliances --
Household -- Major -- Service and
Repair."
Maintain the quality
buitt into your
cooktop
by calling
an authorized
service
company.
To obtain the name and number of the
authorized service company:
[_
Contact the dealer from whom you
purchased your cooktop; or
[_
Look in the Yellow Pages of your
telephone directory under
"Appliances -- Household --
Major -- Service and Repair;" or
[_
Call the Customer Interaction Center.
The toIFfree number is listed in your
Use and Care Guide.
When you call, you will need:
E_The
cooktop model number.
E_The
cooktop serial number.
Both numbers are listed on the
model/serial rating plate located on the
underside of cooktop burner box.
Part No. 8286553
Printed
in U.S.A.
Q 2005 Whirlpool
Corporation
Benton
Harbor, Michigan
49022
04/2005