CENTURION SYSTEMS G-SPEAK ULTRA Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla System interkomu CENTURION SYSTEMS G-SPEAK ULTRA. CENTURION SYSTEMS G-SPEAK ULTRA 2 stron. Gsm-based intercom system

Drukuj stronę

CENTURION SYSTEMS G-SPEAK ULTRA Skrócona instrukcja obsługi

Voltage/Firmware/Date & Time Screen

•

Supply Voltage

•

Time

•

Firmware Version

•

Date

Phone Number Screen

Device SIM Phone Number.

Airtime Balance Screen

Press Enter to Refresh Airtime

Balance from Network Provider.

GSM Antenna Selected Screen

Internal GSM Antenna Selected

(default).

External GSM Antenna Selected

(connect own Antenna to SMA

connector).

Press Enter to change between

Internal and External Antennas.

Gate Status Screen

Gate Closed

Gate Opening

Gate Open

Gate Status Warning

SIM Screen

SIM PIN OK

SIM PIN Incorrect

SIM Error

IMEI Screen

Displays the device's IMEI number

Gate station Voice Numbers

Displays the primary and secondary Voice

Numbers allocated to their respective

buttons

TABLE 3

10. Configurations

10.1. Removing the Mounting Plate and Fascia

To access the terminal blocks of the G-SPEAK ULTRA, the back plate and

fascia need to be removed. Follow the instructions below to do this.

10.1.1. Removing the Mounting Plate

Gently pull the two clips at the back backward to release the main G-SPEAK

ULTRA unit, and lift the unit out of the mounting plate.

Main Unit

Mounting Plate

Clips

FIGURE 5

10.1.2. Removing the Fascia

The fascia can be removed by inserting the tips of one's fingers into the

slots (as shown in Figures 6 and 7), and pulling outward and upward. The

fascia should pop off without effort.

Fascia

Slots

FIGURE 6

Fascia

Main Unit

FIGURE 7

Reverse the procedure under Section 10.1 to re-assemble the G-SPEAK

ULTRA.

10.2. Installation

10.2.1. G-SPEAK ULTRA Mounting

10.2.1.1. Wall-mounting

The Mounting Plate is used to mount the G-SPEAK ULTRA device to a wall.

Use four screws with wall anchors (not supplied) to secure Mounting Plate.

Mounting

screws

(Not Supplied)

Wall

anchors

Mounting

Plate

FIGURE 8

Clip the G-SPEAK ULTRA main unit into the mounting plate after it has been

secured to the wall; a 'click' will be heard if done correctly.

Mounting

Plate

Main Unit

FIGURE 9

10.2.1.2. DIN Rail-mounting

Should the G-SPEAK ULTRA need to be mounted onto a DIN-rail, a DIN-rail

mounting kit is available. Enquire at Centurion Systems (Pty) Ltd for more

information.

Secure the DIN-rail clips to the back of the mounting plate using four (4)

screws.

Mounting

Plate

DIN-rail

Mounting

Screws

Clips

FIGURE 10

Position the bottom of the DIN-rail clips onto the rail, and clip the top end into

position(A). A 'click' will be heard if it has been done correctly(B). Clip the

G-SPEAK ULTRA main unit into the Mounting plate after it has been secured to

the wall; another 'click' will be heard if done correctly.

DIN-rail

Clip

'click'

Mounting

DIN-rail

Plate

Clip

FIGURE 11

To remove the unit from the DIN-rail, remove the main unit from the mounting

plate as described in Section 10.1. Insert a small flat screwdriver into the

hole(s) shown in Figure 12, and gently pry the clips from the rail.

Holes for

Mounting

Screwdriver

Plate

DIN Rail

FIGURE 12

10.2.2. Calling Module

Recommendations for wall mountings

1. Position the Calling Module on wall adjacent to entrance gate or door.

2. Mount at a height that allows for comfortably speaking into the microphone.

The recommended height is 1600mm above ground level.

Recommendations for Goose-neck mountings

1. Ensure that the Calling Module does not protrude too far into the driveway.

2. The Calling Module must not be set too far back and must be easily

accessed from a vehicle.

3. The height should allow for comfortably speaking into the microphone.

Gate Station Mounting instructions

Carefully remove the front cover of the gate station. Insert screwdriver as

shown, unclip the Calling Module and remove it from the base.

Calling

Small flat

screwdriver

Module

Slot

Back /

Mounting panel

FIGURE 13

The Mounting Panel is used to mount the calling module to a wall or

goose-neck. Use two screws with wall anchors (not supplied) to secure the

Mounting panel to a wall, or two screw to secure it to a goose-neck.

If the cable is being routed into the unit from a concealed conduit behind the

base, knock out one of the cable entry holes provided in the base and feed

through the cable. Ensure that at least 100mm of cable extends out of the wall

or goose-neck.

Ensure that sealing washer is fitted and closes off the mounting hole to

prevent water ingress.

Sealing

washer

Screw

Anchor

Back /

Mounting panel

FIGURE 14

Run the cable through the base, hook the Calling Module into the base as

shown below and clip the Calling Module back into position.

Calling

Module

Cable

Back /

Mounting panel

FIGURE 15

If the cable is surface-mounted, route the cable into the unit from underneath.

Terminate the cables into the voice communication terminals by following the

wiring diagram found under Section 10.4.

Write Call Button labels, insert into lens(es) and clip lens(es) back onto chassis.

Cable

Call Button

Labels

Mr. X

Mr. Y

Cable entry

behind the base

Cable

below the base

FIGURE 16

Clip the front cover back into position and secure it with the fixing screw

provided in the kit.

Front Cover

Calling

Module

Screw

FIGURE 17

10.3. Configuration

1. Complete the wiring of the unit as per Section 8 and 10.4 of this document.

2. Power up the device and verify that the device connects to the G-WEB

platform by referring to the LCD home screen.

3. Navigate your Internet browser to http://www.gweb.co.za

(or www.g-web.com.au for Australia and New Zealand) and login to your

existing profile or, alternatively, register a new profile.

4. On the My Devices page, select Add New G-SPEAK ULTRA Device and follow

the onscreen instructions to associate the device to your profile.

5. Configure the device with the desired settings using your online portal.

10.4. Wiring Diagrams

Do not mount close

to DOSS sensor

or remote receiver.

G-SPEAK

ULTRA

GND

IO1

IO2

IO3

IO4

VIN NEG

Quick Add:

To instantly associate a device to your online profile, scan the

QR code using your mobile phone and any universal QR scanner

mobile application.

10.3.1. G-WEB

All features – both basic and advanced – can be easily, and remotely,

configured via the G-WEB online interface. By simply logging into G-WEB

using any Internet-enabled device, one can add and delete devices, specify

text for input and output notifications and activations, modify device

characteristics and a plethora of other features, all from the comfort of one's

home or office. G-WEB can be accessed by navigating to http://www.gweb.

co.za (or www.g-web.com.au for Australia and New Zealand). Note that it

will be necessary to register if you have not previously done so.

10.3.2. SMS Commands

The table below lists the optional basic SMS commands available on the

G-SPEAK ULTRA. All basic and advanced configurations can be done via the

G-WEB online portal.

SMS Command

Description

Device Status Request to which the

device will respond with the following

information:

P.XXXX

.STATUS

• IMEI

• I/O Status

• Supply Voltage

• Firmware Version

• Signal Strength

• Relay Status

• Device date & time

Add New Phone Number

P.XXXX.

Adds a new phone number to Profile 0 and

AB.27821234567.BU1

to Button1.

P.XXXX.

Add Secondary Phone Number

AB.27831234567.

Adds a second phone number to Profile 0

BU1.2

and to Button1.

Delete a specific access number

P.XXXX.DB.BU1

Delete and clear all Voice Phones assigned

to Button 1.

IO Status Request

P.XXXX.IO

This includes custom IO and state names

configured on G-WEB

1. XXXX = Device Default Password

TABLE 4

Calling

Module

D-Series

Controller

FIGURE 18