IKEA LUFTIG HW400 Instrukcja instalacji i użytkowania - Strona 7
Przeglądaj online lub pobierz pdf Instrukcja instalacji i użytkowania dla Hob IKEA LUFTIG HW400. IKEA LUFTIG HW400 8 stron. Range hood
Również dla IKEA LUFTIG HW400: Podręcznik (16 strony), Podręcznik użytkownika (16 strony), Podręcznik użytkownika (16 strony)
Drukuj stronę
61833050a.fm Page 7 Tuesday, February 21, 2006 7:53 PM
PROTECTING THE ENVIRONMENT
1. Packaging
Packaging materials are 100% recyclable and are marked
with the recycling symbol
. Dispose of packaging materials
in compliance with local waste disposal regulations. Packaging
materials can be dangerous for children. Keep packaging
materials (plastic bags, polystyrene, etc.) well out of their
reach.
2. Appliance
The appliance itself is made from recyclable materials.
Dispose of it in accordance with local waste disposal
regulations. Cut off the mains lead to render the appliance
unusable before disposing of it. Do not dispose of the appliance
in the environment. Take it to a proper waste disposal centre.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
WARNING!
• Do not allow children or infirm persons to operate
the appliance without supervision.
• Make sure that children do not play with the
appliance.
1. Do not connect the appliance to the mains electricity
supply until installation is completed. Always disconnect
the hood from the mains before performing any cleaning
or maintenance.
2. Do not "flambé" food under the hood. Naked flames
could cause fire.
3. Do not leave pans unattended when frying. Cooking oil
can catch fire.
4. Regular cleaning and maintenance is essential to correct
functioning and good performance. Regularly remove dirt
deposits. Regularly clean or replace filters. Never use
flammable materials as hoses for extracted air.
5. If the hood is used together with non-electrically powered
appliances, ambient negative pressure must not exceed
-5
4Pa (4 x 10
bars). Make sure that the room is
adequately ventilated.
Electrical connections
Before connecting the hood to the mains, make sure that the
voltage specified on the data plate corresponds to the voltage
in your home. The data plate is located inside the hood
behind the grease filter.
If the appliance is fitted with a power supply cable and plug,
the plug must be inserted in an accessible socket.
If the hood does not come pre-fitted with a mains plug, fit
one that conforms to applicable standards or use a double-
pole switch with a minimum breaking gap of 3 mm.
Replacement of the power supply cable with power plug or
flexible cable may only be carried out by an authorized
Service Centre or a qualified electrician.
5019 618 33050/A
Declaration of conformity
This product has been designed, manufactured and sold in
conformity to the following standards:
-
safety objectives of the "Low Voltage" Directive
73/23/EEC
-
protection requirements of "EMC" Directive 89/336/
EEC amended by Directive 93/68/EEC.
Trouble-shooting guide
Hood does not work:
• Is the power plug properly inserted in the mains socket?
• Is there a power failure?
• Is the mains fuse OK?
The hood is not extracting efficiently:
• Is the right extraction speed selected?
• Do the filters need to be cleaned or replaced?
• Are the air outlets blocked?
Light does not work:
• Does the bulb need to be replaced?
• Is the bulb correctly fitted?
• Is the mains fuse OK?
AFTER-SALES SERVICE
Before calling Technical Assistance
1. Check to see if you can fix the problem yourself
(see "Trouble-shooting guide"").
2. Switch the hood off for a few minutes then switch it back
on and see if the problem has gone.
3. If the problem persists, call Technical Assistance.
Specify:
• the nature of the problem,
• the model of hood, stated on the data plate inside the
hood, accessible by removing the grease filters.
• your full address,
• your telephone number and area code.
• the service code (the number appearing below the word
SERVICE on the data plate inside the hood behind the
grease filter).
If any repairs are needed, contact an authorised Service
Centre (to ensure that only original spare parts are used and
that repairs are made correctly).
Failure to comply with these instructions may compromise
the safety and quality of the product.
GB