IKEA IH4302SS0 Instrukcje instalacji oraz instrukcja obsługi i konserwacji - Strona 6

Przeglądaj online lub pobierz pdf Instrukcje instalacji oraz instrukcja obsługi i konserwacji dla Okap wentylacyjny IKEA IH4302SS0. IKEA IH4302SS0 28 stron. 30"(76.2cm) wall-mount canopy range hood

Drukuj stronę

Example Vent System

,o ° elbow

I-_-_

6. (_.8m)-_,,_l

Wall cap

The following example

falls within the maximum

vent length of

35 ft (10.7 m).

1 - 90 ° elbow

1 - wall cap

8 ft (2.4 m) straight

System length

= 5.0 ft (1.5 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

= 13 ft (3.9 m)

IMPORTANT: Observe all governing codes and ordinances. Save

Installation Instructions for electrical inspector's use.

It is the customer's responsibility

to contact a qualified electrical

installer, and to ensure that the electrical installation is adequate

and in conformance

with National Electrical Code, ANSl/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended

that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch

Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

•

A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is

required.

•

Do not ground to a gas pipe.

•

Check with a qualified electrician if you are not sure range

hood is properly grounded.

•

Do not have a fuse in the neutral or ground circuit.

•

The range hood must be connected with copper wire only.

•

The range hood should be connected directly to the fused

disconnect

(or circuit breaker) box through flexible armored or

nonmetallic sheathed copper cable. It is recommended

that a

separate circuit serving only this hood be provided.

•

Wire sizes (copper wire only) and connections must conform

with the rating of the appliance as specified on the model/

serial rating plate. The model/serial

plate is located behind

the filter on the rear wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSl/NFPA 70 (latest edition), or CSA

Standards C22.1-94,

Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

•

A 1/2"(12.7 mm) UL listed or CSA approved strain relief must

be provided at each end of the power supply cable (at the

range hood and at the junction box).

INSTALLATION INSTRUCTIONS

It is recommended

that the vent system be installed before

hood is installed.

Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting

frame must be

constructed.

•

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

•

Check your ceiling height and the hood height maximum

before you select your hood.

Excessive

Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

If possible, disconnect

and move freestanding

or slide-in

range from cabinet opening to provide easier access to rear

wall. Otherwise, put a thick, protective covering over

countertop,

cooktop or range to protect from damage or dirt.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling

the range hood. Cover

that surface with a protective covering.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Using 2 or more people, lift range hood onto protective

surface.

Determine and mark the centerline on the wall where the

hood will be installed.

Select a mounting height above the cooking surface to the

bottom of the hood which is between a minimum of

30" (76.2 cm) and a suggested maximum of 36" (91.4 cm).

Mark a reference line on the wall.

NOTE: For installation locations with reduced ceiling heights,

the hood may be installed using the lower vent cover for both

vented and non-vented (recirculating) installations.