KitchenAid YKGCT305E Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Płyta grzewcza KitchenAid YKGCT305E. KitchenAid YKGCT305E 10 stron. 30" ana 36" gas sealed burner glass cooktops

Drukuj stronę

Tools needed for

installation:

pencil

pipe wrench

screwdriver

adjustable

wrench

uler

Gas supply

requirements

Fire Hazard

Cooktop must be connected to a regulated

gas supply.

Do Not use an open flame to test for leaks

from gas connections.

New, CGA/A.G.A.

design-approved,

flexible

gas line should be used when codes

permit.

Failure to follow

these instructions could

result in a fire or explosion.

Observe all governing codes and ordinances.

This installation instruction must

conform with local codes and ordinances. In the

absence of local codes, installations must

conform with CANI -- B149.1 or 2.

shutoff valve

to cookto_

to gas

supply line

F..

The supply line shall be equipped with an

approved shutoff valve. This valve should be

located in the same room as the cooktop and

should be in a location that allows ease of

opening and closing. Do Not block access to

shutoff valve. The valve is for turning on or

shutting off gas to the appliance.

G..

If rigid pipe is used as a gas

supply line, a combination of pipe fittings must

be used to obtain an in-line connection to the

cooktop. All strains must be removed from the

supply and fuel lines so cooktop will be level and

in line.

H..

The regulator must be checked at a

minimum 1-inch (2.5-cm) water column above

the set pressure. The inlet pressure to the

regulator should be as follows for operation:

NATURAL GAS:

Set pressure 4 inches (10.2 cm)

Supply pressure 7 to 14 inches (17.8 cm to

35.5 cm) maximum

_..

Line Pressure Testing:

Testing above 112 psi (3.5kPa) (gauge)

The cooktop and its individual shutoff valve must

be disconnected from the gas supply piping

system during any pressure testing of that

system at test pressures greater than 1/2 psi

(3.5 kPa).

Testing at 112 psi (3.5kPa) (gauge) or lower

The cooktop must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure testing

of the gas supply piping system at test pressures

equal to or less than 1/2 psi (3.5 kPa).

Electrical

requirements

Recommended

grounding

method

For your personal safety, this appliance must

be grounded.

This appliance is equipped with

a 3-prong grounding plug. To minimize possible

shock hazard, the cord must be plugged into a

mating 3-prong grounding-type wall receptacle,

grounded in accordance with the Canadian

Electrical Code (CSA) -- latest edition and local

codes and ordinances•

See Figure 1.

If a mating wall receptacle is not available, it is

the personal responsibility and obligation of the

customer to have a properly grounded, 3-prong

wall receptacle installed by a qualified

electrician.

3-prong

grounding-type

wall receptacle I\_--._1

3.prong __

I_JJ

grounding

L I

6')/11

plug

,JPII

grounding

IL \ II

/prong

power

supply cord

Figure I

Now start...

With cooktop

in kitchen.

Remove shipping materials and tape

from cooktop.

Remove pressure

regulator and hardware package from

side of carton. Write down the model and serial

numbers on the front of these instructions

before

installing the cooktop. The numbers are on the

model/serial rating plate located on the bottom of

the cooktop burner box.

B..

Input ratings shown on the model/serial

rating plate are for elevations up to 2,000 feet

(610m). For elevations above 2,000 feet (610m),

ratings are reduced at a rate of 4% for each

1,000 feet (305m) above sea level• (For the USA

only.)

C..

This cooktop is equipped for use with

NATURAL gas. The model/serial

rating plate,

located on the bottom of the cooktop, has

information on the type of gas that can be used.

If this information does not agree with the type of

gas available, see your KitchenAid dealer or

authorized parts distributor.

D..

Provide a gas supply line of 3/4"

(1.9cm) rigid pipe to the cooktop location. A

smaller size pipe on long runs may result in

insufficient gas supply. Pipe-joint compounds,

made for use with NATURAL and L.P. gas, must

be used.

.....

E..

If local codes and ordinances permit,

CGA/A.G.A.

design-certified,

flexible metal

tubing is recommended

for connecting this

cooktop to the gas supply line. Do Not kink or

damage the flexible tubing when moving the

cooktop. A 3/8" (.95cm) male pipe thread is

needed for connection to pressure regular

female pipe threads.

Electrical Shock Hazard

Electrically ground the cooktop.

Do Not change the power supply cord plug.

L__

Remove cooktop, burner grates and

If plug will not fit the outlet, have a proper

caps package from shipping box.

outlet installed by a qualified electrician.

Do Not use an extension cord.

Failure to follow these instructions could

result in death, fire or electrical shock.

_/__

"___!

Do Not ground to a gas pipe.

Check with a qualified electrician if you are

not sure whether the cooktop is properly

grounded.

A 120-volt, 60-Hz, AC-only, 15-or 20-ampere,

\_,

-,,

fused electrical supply is required.

A time-delay

\_t,\_.

___ '_'_

fuse or circuit breaker is recommended.

It is

recommended that a separate circuit serving

only this appliance be provided.

Electronic ignition systems operate within wide

voltage limits, but proper grounding and polarity

are necessary for proper operation.

In addition

to checking that the outlet provides 120-volt

power and is correctly grounded, the outlet must

be checked by a qualified electrician to see if it is

wired with correct polarity. A wiring diagram is

provided on the back cover.

This appliance, when installed, must be

electrically grounded in accordance with local

codes or, in the absence of local codes, with the

current CSA standard C22.1. Canadian Electrical

Code Part 1.

3_n

Remove the paper backing from a

small section of the foam sealing strip•

Place the strip 1/8" (0.3cm) from

cooktop edge on the underside of the

glass. Continue until foam strip completely

outlines the edge of the cooktop. Do Not use

additional sealant around outer edge of cooktop.

Panel B