KitchenAid Dishwahser Instrukcje użytkownika - Strona 5
Przeglądaj online lub pobierz pdf Instrukcje użytkownika dla Zmywarka KitchenAid Dishwahser. KitchenAid Dishwahser 11 stron.
Drukuj stronęOPTION SELECTIONS ~I
OPTIONS
DISH LOAD TYPES
DESCRIPTIONS
USE WITH:
Use for loads with normal
amounts of soi!.
The Steam option adds steam to the cycle. This option
raises the water temperature in the final rinse to
approximately 155°F (68°C). The option adds heat and time
to the cycle.
Heavy Duty or Normal
cycle.
Pans, casseroles, etc. with Activates the PROSCRUB ~'~ spray jets and provides
tough food soil.
intensified water spray to the back of the lower level rack.
May add heat and time to the cycle.
Heavy Duty or Normal
cycle
To sanitize your dishes and
glassware in accordance
with NSF/ANSI Standard
184 for Residential
Dishwashers.
Raises the water temperature in the final rinse to
approximately 155°F (68°C). This high temperature rinse
sanitizes your dishes and glassware in accordance with
NSF/ANSI Standard 184 for Residential Dishwashers.
Certified residential dishwashers are not intended for
licensed food establishments.
The Sanitize or Sani Rinse option adds heat and time to the
cycle.
Normal cycle. Heaw
Duty cycle automatically
uses Sani Rinse. Only
these sanitization cycles
have been designed to
meet the NSF/ANSI
requirements.
Loads containing tough,
baked-on food.
Increases the target water temperature during the wash
portions of the cycle.
Adds heat, wash time and water to the cycle.
Heavy Duty or Normal
cycles
For best drying results, dry
dishes with heat.
Turn OFF when loads contain plastic dinnerware that may be
sensitive to high temperatures.
This option with the use of rinse aid will provide the best
drying performance.
All cycles, except Rinse
Only. Automatic with all
wash cycles unless you
turn it off.
To run your dish washer at
Delays the start of a cycle up to 4 hours.
a later time or during off-
Select a wash cycle and options. Press 4 Hour Delay. Press
peak hours.
START/RESUME. Close the door firmly.
All cycles, except Rinse
Only
Control Lock To avoid unintended use of
your dishwasher, or cycle
and option changes during
a cycle.
To turn on Lock, press and hold Heat Dry for at least
4 seconds.
To turn off Lock, press and hold Heat Dry for at least
4 seconds.
When Control Lock is lit, all buttons are disabled. If you press
any pad while your dishwasher is locked, the light flashes
3 times. The dishwasher door can be opened while the
controls are locked.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the
cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle
will automatically compensate by adding time, heat and water as needed.
CONTROLS AND i
CYCLE STATUS
CONTROL
PURPOSE
COMMENTS
To start or resume a
If the door is opened during a cycle or the power is interrupted, the Start/Resume indicator
wash cycle
flashes. The cycle will not resume until the door is closed and Start/Resume is pressed.
To cancel wash
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher
cycle
drain completely.
¯ wo,h~og
TO follow the
¯ Drying
progress
of your
¯ c~an
dishwasher cycle
¯ Sanitized
Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the Sani Rinse cycle is finished, the Sanitized indicator
glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required
temperature. The light goes off when you open and close the door or press CANCEL.