Briteq BEAMSPOT1-DMX WW Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Sprzęt oświetleniowy Briteq BEAMSPOT1-DMX WW. Briteq BEAMSPOT1-DMX WW 12 stron.

Drukuj stronę

ENGLISH

RDM FUNCTIONS / REMOTE SETUP

RDM means "Remote Device Management". This projector works with a brief set of RDM-functions which

means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of

these functions are briefly explained below, others will be added in the future.

 The DMX-controller sends out a "discovery command", all RDM devices respond and send their unique

device ID.

 The DMX-controller asks each RDM device for some basic data so it knows which devices are connected.

The projector will respond:

 Device name:

 Manufacturer:

 Category:

 Firmware: x.x.x.x

 DMX address: xxx

 DMX footprint: xx

 Personality: xx

 The DMX-controller can send certain commands to each RDM device which allow remote setup of the

units. Thanks to this the projector can be setup remotely.

The following functions can be managed remotely:

No more need to take a ladder and set all units one by one!

 DMX START ADDRESS: The start address can be set remotely from 001 to xxx.

 PERSONALITY: The DMX working mode (DMX-chart) can be set remotely.

These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMX-

controller and send these data to all projectors at once. More functions will be added later.

OPERATING INSTRUCTIONS

Note: when the projector is switched on the display shows "UPDATE WAIT ..." This message informs you

that IF you want to upgrade the firmware, you should do it while this message is shown on the display. For

normal use you can ignore this message completely.

A. Standalone 1unit:

 Just connect the projector to the mains.

 Adjust the master dimmer [MASTER DIM] if necessary

 Refer to chapter HOW TO SETUP to learn how to set the menu options.

B. Two or more units in master/slave setup:

 Connect the units together. Refer to the chapter "electrical installation" to learn how to do this.

 Adjust the master dimmer [MASTER DIM] on the 1

 Set all the other projectors in SLAVE mode

 The slave projectors will now follow the settings of the master projector so they all work

synchronously.

C. Controlled by universal DMX-controller:

 Connect all units together. Refer to the chapter "Electrical installation for two or more units in DMX-

mode" to learn how to do this (don't forget to address all units properly!)

 Connect all units to the mains and turn on the DMX controller.

Since each unit has its own DMX-address, you can control them individually. Remember that each unit

can use a different number DMX-channels, depending on the DMX-mode you have selected in the

menu. See the different DMX charts below:

DMX Chart for the 1 channel DMX-Mode

Channel:

Value:

000-255

DMX Chart for the 2 channel DMX-Mode

Channel:

Value:

000-255

000-005

006-255

BRITEQ

BEAMSPOT1-DMX NW (WW)

Briteq

LED Dimmer

(firmware version of the projector)

(current DMX start address of the projector)

(number of DMX-channels used by the projector)

(current personality [or DMX-working mode] used by the projectors)

Function:

Master dimmer (0-100%)

Function:

Master dimmer (0-100%)

Open

Increasing strobe speed

8/9

OPERATION MANUAL

unit (master unit).

No strobe

006 = slow 255 = fast

BEAMSPOT1-DMX NW (WW)

Remarks: