ALIBI ali-bc1080e Instrukcja szybkiej instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja szybkiej instalacji dla Kamera bezpieczeństwa ALIBI ali-bc1080e. ALIBI ali-bc1080e 4 stron. Hd-tvi outdoor infrared bullet camera
Drukuj stronę
OSD menu navigation
For the ALIBI HVR: Navigation and settings in the OSD are made through direction keys and the Iris +
and Iris - buttons in the ALIBI HVR PTZ Control panel. See below.
Direction keys
Iris+ Iris–
ALIBI HVR PTZ Control panel
For remote access to the ALIBI HVR: Navigation and settings in the OSD are made through direction
keys and the Iris + and Iris - buttons in the ALIBI HVR PTZ control panel. See above.
The function of the directional keys and Iris buttons are defined in the table below.
Keys
Function
p
Move up in the parameter list
q
Move down in the parameter list.
t
Move to previous page, field, or move the camera left.
u
Move to next page, field, or move field right.
Iris+ (OPEN)
Set parameter value, or open sub-menu
Iris– (CLOSE)
Cancel change of parameter.
Step 4.
Use the OSD menu to configure the camera
The abbreviated OSD menu tree is shown below.
MAIN MENU
VIDEO
VIDEO OUT (frame rate)
OUT
DAY/
MODE
NIGHT
AWB
MODE
AE
MODE
SPECIAL
PRIVACY
EFFECT
Video settings
SYSTEM
CAM ID
EXIT
SAVE/
EXIT
www.observint.com
3
Direction keys
Iris+ Iris–
ALIBI HVR remote access PTZ control panel
EXT
COLOR
B/W
AUTO
AUTO
USER
PUSH
Set
Temp (K)
ESC
HOLD
DC
HLC
MOTION
FLIP
MIRROR
ID DISPL
LANGUAGE
FACTORY
NAME DISPL
INIT
EXIT
OSD Definitions:
AE: Set automatic exposure mode.
AGC (Automatic Gain Control): Higher gain increases brightness but also increases any noise. When a high
gain level is applied, higher noise levels are seen.
AWB (Automatic White Balance): The function to search for the color which is matched well with the
ambient environment.
BLC (Back Light Compensation): This feature enables the camera to compensate for strong back light
conditions in a selected area of the image.
DELAY TIME (DAY/NIGHT): This option specifies the switching time from color to B/W and B/W to color.
D TO N, N TO D: This option sets the AGC brightness when switching from day to night and night to day.
FACTORY INIT: Select FACTORY to reset the camera configuration to the factory default values.
FLICKER: Feature used to reduce noise in the image produced by AC current at 60 Hz.
FLIP: This feature provides an image that is reflected vertically.
HLC (High Light Compensation): HLC feature is used to identify and suppress the strong light sources that
usually flare across a scene. It improves the detail of the image that would normally be hidden.
LSC (Lens Shading compensation): This feature brightens the image in shaded areas.
MIRROR: This feature provides an image that is reflected horizontally.
MOTION: The MOTION feature allows you to quickly identify areas of the image where motion is detected.
PRIVACY: The PRIVACY feature allows you to block areas of the image from being seen. Use the SX, EX, SY,
and EY parameters to set the right, left, up and down limits of the privacy area.
SAVE/EXIT: Save the current configuration settings and close the OSD. The settings are retained even after
if the camera is powered off, and then on again.
SX, EX, SY, EY: Sets the start and end X boundaries and the start and end Y boundaries of a PRIVACY or
MOTION area.
Examples
The following examples provided demonstrate how to use the menus to perform basic configuration tasks.
For clarity, the background video image was removed in the screens included here.
Example 1: Change video frame rate
The video frame rate parameter can be set using the Main Menu VIDEO OUT submenu. To change the
setting:
1.
Open the OSD Main Menu (see "Step 3. Open the OSD menu" on page 2).
With the > marker at the VIDEO OUT entry, click the Iris + button to open the VIDEO OUT submenu
2.
(see the right screen above.
With the > marker at the FRAME RATE entry, click the t or u button to decrease or increase the
3.
frame rate.
Click the q button to position the > marker at RETURN, and then click the Iris + button to return
4.
to the previous menu (MAIN MENU).
Click the p button to position the > marker at EXIT, and then click the Iris + button to open the
5.
EXIT submenu.
© 2015 Observint Technologies. All rights reserved.