Makita 0088381640978 Instrukcja obsługi - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Elektronarzędzie Makita 0088381640978. Makita 0088381640978 17 stron. Cordless plate joiner

Drukuj stronę

Adjust the angle guide height so that the blade is

centered in the board thickness.

Align the center mark on the base with the pencil

line on the workpiece.

Switch on the tool and gently push it forward to

extend the blade into the workpiece.

Gently return the tool to the original position after the

adjusting screw reaches the stopper.

For Corner Joint and T-Butt Joint only

Clamp the horizontal workpiece to the workbench.

For Miter Joint only

Clamp the other workpiece to the workbench with

the mitered edge facing up.

For Frame Joint and Edge-To-Edge Joint only

Clamp the other workpiece to the workbench.

10. For Corner Joint only

Place the tool on the workpiece so that the blade is

facing down.

For T-Butt Joint only

Remove the angle guide from the tool. Place the tool

on the workpiece so that the blade is facing down.

11. Repeat the steps 6 – 8 to groove in the horizontal or

the other workpiece.

If you do not need to center the blade in the board thick-

ness, proceed as follows:

For Corner Joint, Miter Joint, Frame Joint and Edge-

To-Edge Joint only

• Remove the angle guide from the tool. Set the fence at

90° for Corner Joint, Frame Joint and Edge-To-Edge

Joint or at 45° for Miter Joint.

• Follow steps 1 – 11 excluding steps 5 and 10 described

above.

For T-Butt Joint only

• Fit the two workpieces together as they will appear in

the finished joint position.

• Lay the vertical workpiece on the horizontal one. Clamp

both workpieces to the workbench.

• Remove the angle guide from the tool.

• Follow the steps 2, 4, 6, 7, 8 and 11 described above.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool's air vents or whenever the vents start to

become obstructed. (Fig. 27)

Replacing carbon brushes

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes. (Fig. 28)

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it

up. (Fig. 29)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 30)

Reinstall the holder cap cover on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Angle guide

• Dust bag

• Set plate

• Lock nut wrench

• Plate joiner blades

• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

Noise

The typical A-weighted noise level determined according

to EN60745:

Model BPJ140

Sound pressure level (L

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model BPJ180

Sound pressure level (L

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: cutting grooves in MDF

Vibration emission (a

Uncertainty (K): 1.5 m/s

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

): 73 dB (A)

): 74 dB (A)

): 2.5 m/s

or less

ENG905-1

ENG900-1

ENG901-1