HIKVISION DS-7208HTI-K2 Skrócona instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla DVR HIKVISION DS-7208HTI-K2. HIKVISION DS-7208HTI-K2 15 stron.
Drukuj stronęSymbol Conventions
The symbols that may be found in this document are defined as follows:
Symbol
Description
Provides additional information to emphasize or supplement important points of the main text.
Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or
unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.
Safety Instructions
•
Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
•
In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Refer to technical specifications
for detailed information.
•
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100 to 240 VAC, 12 VDC, or 48 VDC
according to the IEC60950-1 standard. Refer to technical specifications for detailed information.
•
Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.
•
Make sure that the plug is firmly connected to the power socket.
•
If smoke, odor, or noise rise from the device, turn off the power at once and unplug the power cable, and then contact the service center.
Preventive and Cautionary Tips
Before connecting and operating your device, be advised of the following tips:
•
Ensure unit is installed in a well-ventilated, dust-free environment.
•
Unit is designed for indoor use only.
•
Keep all liquids away from the device.
•
Ensure environmental conditions meet factory specifications.
•
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive
electronics within the unit.
•
Use the device in conjunction with an UPS if possible.
•
Power down the unit before connecting and disconnecting accessories and peripherals.
•
Use only a factory recommended HDD for this device.
•
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries
according to the instructions provided by the battery manufactu
Mandatory Electrical Requirements
Hikvision requires the following conditions and equipment for all of its electronic equipment:
•
Grounding
Ensure good conductivity for all ground paths; examine ground path contact surfaces for defects, dirt, corrosion, or non-conductive coatings that may
impede conductivity. Repair or clean contact surfaces as necessary to assure good metal-to-metal contact. Ensure fasteners are properly installed and
tightened.
•
Electrical Wiring
Ensure your outlets are properly wired. They can be checked with an electrical outlet tester.
•
Surge Suppressor (Required)
Hikvision is not responsible for any damage to equipment caused by power spikes in the electrical power grid. Use of a surge suppressor meeting the
following specifications is mandatory for all Hikvision electronic equipment:
•
Specifications
˗ Listed by Underwriter's Laboratories, meeting the UL 1449 Voltage Protection Rating (VPR)
˗ Minimum protection of 1,000 joules or higher
˗ Clamping voltage of 400 V or less
˗ Response time of 1 nanosecond or less
•
Usage
˗ Surge suppressors must not be daisy chained with power strips or other surge suppressors
•
Maintenance
˗ Replace after a serious electrical event (e.g., lighting blew out a transformer down the street)
˗ Replace yearly in storm-prone areas
˗ Replace every two years as routine maintenance
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
rer.
Rev. 010918NA