Makita 5603R Instrukcja obsługi - Strona 8

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Elektronarzędzie Makita 5603R. Makita 5603R 13 stron. 165/190/235 mm
Również dla Makita 5603R: Instrukcja obsługi (13 strony), Podręcznik (15 strony), Instrukcja obsługi (13 strony), Instrukcja obsługi (13 strony), Instrukcja obsługi (12 strony), Instrukcja obsługi (16 strony)

Drukuj stronę

Riving knife adjustment (Fig. 4)

Use the socket wrench to loosen the hex head socket

bolt for the riving knife adjustment, then raise the

safety cover. Move the riving knife up or down over

the two protuberances for settings indicated in the

illustration, so as to obtain the proper clearance

between the riving knife and saw blade.

CAUTION:

Ensure that the riving knife is adjusted such that:

The distance between the riving knife and the toothed

rim of the saw blade is not more than 5 mm.

The toothed rim does not extend more than 5 mm

beyond the lower edge of the riving knife.

Adjusting depth of cut (Fig. 5)

Loosen the lever on the depth guide and move the

base up or down. At a desired depth of cut, secure the

base by tightening the lever.

CAUTION:

• Use a shallow depth of cut when cutting thin work-

piece for cleaner, safer cuts.

• After adjusting the depth of cut, always tighten the

lever securely.

Adjusting for bevel cuts (Fig. 6)

• Loosen the thumb nuts in front and back, and tilt the

tool to the desired angle for bevel cuts (0 – 45°).

Secure the thumb nuts tightly in front and back after

making the adjustment.

Sighting (5603R, 5705R) (Fig. 7)

For straight cuts, align the right notch on the front of

the base with your cutting line on the workpiece.

For 45° bevel cuts, align the left notch with it.

Top guide (5903R) (Fig. 8)

Align your sight line with either the 0° notch for

straight cutting or the 45° notch for 45° angle cuts.

Switch action (Fig. 9)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to

the ''OFF'' position when released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

depress the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

Operation (Fig. 10)

Hold the tool firmly. Set the base plate on the work-

piece to be cut without the blade making any contact.

Then turn the tool on and wait until the blade attains

full speed. Now simply move the tool forward over the

workpiece surface, keeping it flat and advancing

smoothly until the sawing is completed. To get clean

cuts, keep your sawing line straight and your speed of

advance uniform.

CAUTION:

• The riving knife should always be used except when

plunging in the middle of the workpiece.

• Do not stop the saw blade by lateral pressure on the

disc.

Guide rule (Fig. 11)

The handy guide rule allows you to do extra-accurate

straight cuts. Simply slide the guide rule up snugly

against the side of the workpiece and secure it in

position with the screw on the front of the base. It also

makes repeated cuts of uniform width possible.

Joint assembly (Fig. 12 & 13)

(for connecting a vacuum cleaner)

When you wish to perform clean cutting operation,

connect a vacuum cleaner to your tool. Install the joint

on the tool using the screw. Then connect a hose of

vacuum cleaner to the joint.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 14 & 15)

Replace carbon brushes when they are worn down to

the limit mark. Both identical carbon brushes should

be replaced at the same time.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.