KitchenAid 8053714 Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Zakresy KitchenAid 8053714. KitchenAid 8053714 7 stron. 30" electric freestanding range

Drukuj stronę

$j Fp Connect

gd :gg power

supply

cord

or power

supply cable

Electrical Shock Hazard

Turn power supply off before connecting

wires.

Use 8-gauge solid copper wire,

Electrically ground range.

Failure to follow these instructions

can result

in death, fire, or electrical shock,

lis range may be connected directly to the fuse

rconnect or circuit breaker box; or with a L&L.-

ted, 40.ampere range power supply cable.

ipending on your electrical supply, make the

quired three-wire or four-wire connection.

U.L.-listed conduit

connector.

Disconnect the power supply.

Remove the knockout for the power supply

cable.

I Assemble a U.L.-listed conduit connector in

the power supply cable opening.

1 3.

Strip outer covering back 3 inches from end,

exposing wires. Strip the insulation back

1 inch from the end of each wire.

Four-wire electrical connection:

Before moving range across floor, check that

range is still on cardboard shipping base to

protect floor covering.

ground

link

ground-link

screw

Form the bare wire into a

"U"-shaped hook.

Insert the power supply cable

through the conduit connector,

allowing enough slack to easily

attach the

7. I

wiring terminal block.

Complete electrical connection according to

your type electrical supply {"Three-wire

electrical connection"

or "Four-wire

electrical connection.")

lree-wire electrical connection:

Figure 7

anti-tip

bracket

I Making sure the anti-tip bracket is

installed:

Look for the anti-tip bracket securely attached

to floor.

Slide range back so rear range foot is under

anti-tip bracket.

line 1

U.L. listed

conduit

connector ar rd

Power suppl

cable

ound -

silver-colore

terminal blo

screw

Figure 8

If installing the range in a mobile home,

fou MUST secure the range to the floor. Any

nethod of securing the range is adequate as

ong as it conforms to the standards in the

'Mobile home installation"

instructions, Page 2.

Jse this method for mobile homes and

vhenever four-wire installation

is required.

8. Remove the ground-link screw from the

range frame. Save the ground-link

screw. Bend up the ground link so that it

does not contact the range. See Figure 7.

9. Connect the bare ground wire from

power supply cable to the range using the

ground-link screw. The ground wire

must be attached first and must not

contact any other terminal. See Figure 8.

0. Connect the neutral wire (white wire) to the

center, silver-colored terminal screw on the

terminal block using the brass terminal

nuts that are attached to the inside of the

terminal block cover. See Figure 8.

1. Connect the other two wires to the outer

terminals on the terminal block.

See Figure 8.

2. Do NOT loosen the factory-installed

nuts

already on the terminal. Tighten nuts with

3/8" nut driver for proper electrical

connection.

3. Tighten the locking ring and clamping

screws of the conduit connector,

4. Replace the terminal block cover.

line

ure 6

Fig!

wet

connector and po

supply

cable,

con

nei

? this method ONLY if local codes PERMIT

lnecting cabinet-ground

conductor to

&al wire of power supply cable.

Use the brass terminal nuts attached to the

inside of the terminal block cover to

connect the neutral wire (white wire) to the

silver-colored terminal screw on the

terminal block. See Figure 6.

Connect the other two wires to outer

terminal screws on the terminal block.

See Figure 6.

Do Not loosen factory-installed

nuts

already on the terminal. Tighten nuts

with 318' nut driver for proper electrical

connection.

Tighten the locking ring and clamping

screws of the conduit connector.

!Ieplace the terminal block cover.

'range is not level, pull range forward until rear

?veling leg is removed from the anti-tip bracket.

/se 3/8" drive ratchet and channel lock pliers to

djust leveling legs up or down until range is

rvel. Push range back into position. Check that

?ar leveling leg is engaged in anti-tip bracket,

ote: Oven must be level for satisfactory baking

bnditions.

anel.

= Replace the storage drawer or lower

Page 5