KitchenAid DISHWASHER Instrukcje użytkownika - Strona 6
Przeglądaj online lub pobierz pdf Instrukcje użytkownika dla Zakresy KitchenAid DISHWASHER. KitchenAid DISHWASHER 10 stron. Drawer dishwasher
Również dla KitchenAid DISHWASHER: Instrukcja instalacji (6 strony), Instrukcje użytkownika (20 strony), Instrukcje użytkownika (5 strony)
Drukuj stronę
OPTION SELECTIONS
OPTIONS
DISH LOAD TYPES
For best drying results, dry
dishes with heat.
To sanitize your dishes and
glassware in accordance
with NSF/ANSI Standard
184 for Residential
Dishwashers.
Loads containing tough,
baked-on food.
To run your dishwasher at
a later time or during off-
peak hours.
Control Lock
To avoid unintended use of
your dishwasher, or cycle
and option changes during
a cycle.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the
cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle
will automatically compensate by adding time, heat and water as needed.
CONTROLS AND
CYCLE STATUS
CONTROL
PURPOSE
To start or resume a
wash cycle
To cancel wash
cycle
To follow the
progress and status
of your dishwasher
cycle
6
DESCRIPTIONS
This option with the use of rinse aid will provide the best
drying performance.
Raises the water temperature in the final rinse to
approximately 155°F (68°C). This high temperature rinse
sanitizes your dishes and glassware in accordance with
NSF/ANSI Standard 184 for Residential Dishwashers.
Certified residential dishwashers are not intended for
licensed food establishments.
The Sanitize or Sani Rinse option adds heat and time to the
cycle.
Increases the target water temperature during the wash
portions of the cycle.
Adds heat, wash time and water to the cycle.
Delays the start of a cycle up to 4 hours.
Select a wash cycle and options. Press 4 Hour Delay. Press
START/RESUME. Close the drawer firmly.
To turn on Lock, press and hold ProDry for at least
3 seconds.
To turn off Lock, press and hold ProDry for at least
3 seconds.
When Control Lock is lit, all buttons are disabled. If you press
any pad while your dishwasher is locked, the light flashes
3 times. The dishwasher drawer can be opened while the
controls are locked.
COMMENTS
If the drawer is opened during a cycle, a delay, or the power is interrupted, the Start/Resume
indicator flashes. To restart the drawer, open the drawer, press Start/Resume and close the
drawer firmly within 4 seconds./
Close the drawer firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher
drain completely. If the Cancel button is pressed a second time, the drawer will turn off.
Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the Sani Rinse cycle is finished, the Sanitized indicator
glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required
temperature. The light goes off when you open and close the drawer or press CANCEL.
The rinse aid low indicator light glows when the rinse aid dispenser needs to be refilled.
USE WITH:
All cycles, except Quick
Cleanup and Rinse
Only. Automatic with all
wash cycles unless you
turn it off.
Sensor Wash, Heavy
Duty and Normal Wash.
Only these sanitization
cycles have been
designed to meet the
NSF/ANSI
requirements.
Sensor Wash, Heavy
Duty or Normal Wash
All cycles, except Rinse
Only
Anytime