E-T-A ESX10-TB-DC 24 V Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wyłączniki automatyczne E-T-A ESX10-TB-DC 24 V. E-T-A ESX10-TB-DC 24 V 8 stron. Electronic circuit protector

Drukuj stronę

Electronic Circuit Protector ESX10-TA/-TB-DC 24 V

Warning

This device is only suitable for operation at 24 VDC (safety

extra-low voltage). Direct connection of this device to a 110 V,

230 V or 400 V power system, or to power systems with a higher

voltage, may consequently result in death, severe personal injury

or substantial property damage. Only qualified personnel should

work on or around this equipment. The product will function

correctly and safely only if it is transported, stored, set up and

installed as intended.

Caution

Electrostatic sensitive devices (ESD) – the device must be opened

only by the manufacturer.

Disposal guideline

Packaging and packing aids can be recycled and should always

be returned to use.

Note

More detailed information can be obtained from local E-T-A subsidiaries

or from the homepage www.e-t-a.de. The product is subject to techni-

cal modifications. In case of doubt the German text takes precedence.

If used under Ex conditions, this device must only be actuated of the

immediate environment is verifiably not classified as a hazardous area.

Automatic start-up of machinery after shut down must be prevented (Ma-

chinery Directive 2006/42/EG and EN 60204-1). In the event of a short

circuit or overload the load circuit will be disconnected electronically by

the ESX10-TA-/TB.

Installation instructions

The type ESX10-TA-/TB can be snapped onto symmetrical rail EN 60715.

Please observe the marking of the ESX10-T signal inputs and outputs,

connection diagrams etc. Before power up the cables have to marked

so as to prevent reverse polarity. The user should ensure that the cable

cross sections of the relevant load circuit are suitable for the current ra-

ting of the ESX10-T used. In the event of Ex applications it has to be

ensured that protection class IP 54 is achieved after installation in a UV-

protected, fully enclosed room / control cabinet. IEC/EN60079-0 and IEC/

EN 60079-14 have be observed for installation.

Safety

This device is not protected against reversed polarity of the input

voltage. It has to be protected against overvoltage > 32 V.

Danger of explosion: Incorrect connection of cables can cause

ignition. The output and the device are protected by an internal,

non-exchangeable blade fuse. Use in aggressive mixed media was

not tested. When mounted side-by-side without convection, the

devices should not carry more than 80 % of its rated load with

100 % ON duty due to thermal effects.

Table

0.5

Current rating (A)

0.5

Max. load (A)

Specifications:

Protection class

EMC

Insulation

coordination

CE logo

CSA

ATEX

Ordering information

Type No.

ESX10

Electronic Circuit Protector, with current limitation

Mounting and design

rail mounting, without signal contact

rail mounting, with aux. contact and hole for signal

busbars/jumpers

Version

standard, without physical isolation

Signal input

10.8

ESX10 -TB-1 0 1-DC 24 V-6 A -E

- 1 -

Instruction Manual

to EN60529

housing IP20, terminals IP20

emitted interference to EN 61000-6-3

noise immunity to EN 61000-6-2

0.5 kV / pollution degree 2, re-inforced

insulation in operating area to

IEC60934 / IEC60664

to 2014/30/EU and 2014/34/EU

UL 2367, File # E306740

Solid State Overcurrent Protectors

UL 508, File # E322549

Industrial Control Equipment

ISA 12.12.01-2015, File # E320024

CSA C22.2 No: 14 File # 016186

CSA C22.2 No: 142 File # 016186

CSA C22.2 No: 213

IEC/EN60079-0 /-14/-15

II 3G Ex nA II B T4 Gc X

without signal input

with control input IN+ (only ESX10-T.-114)

with reset input RE (only ESX10-T.-124,

ESX10-T.-127)

Signal outputs

without signal output (only ESX10-TA)

signal contact N/O

signal contact N/C

status output SF (only ESX10-T.-114,

ESX10-T.-124)

inverse status output SF (only ESX10-T.-127)

Operating voltage

DC 24 V

rated voltage DC 24 V

Current rating

0.5...12 A

Approvals

ATEX

Ordering information