KitchenAid KEBC167MSS00 Instrukcje instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Piekarnik KitchenAid KEBC167MSS00. KitchenAid KEBC167MSS00 5 stron. 36" electric built-in single oven
Również dla KitchenAid KEBC167MSS00: Lista części (7 strony)
Drukuj stronę
ff codes permit and a separate grounding wire is
used, it is recommended that a quaHified eHectrician
determine that the grounding path and wire gauge
is in accordance with Mccall codes.
Do Not ground to a gas pipe.
Check with a quaHified eHectrician if you are not sure
oven is properHy grounded.
Do Not have a fuse in the neutraHor grounding
circuit.
Oven must be connected to the proper eHectricaH
voHtageand frequency as specified on the
modeH/seriaH rating pilate. (The modeH/seriaH rating
pilate is Hocatedon the oven door or on the oven
frame.}
[_ Models rated at 7.2 kW and below at 240 volts
(5.4 kW and bellow at 208 voHts)require a separate
30oampere circuit.
[_ A timeodeHayfuse or circuit breaker is
recommended.
[_ Connect directHyto the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metaHHic sheathed, copper came (with
grounding wire).
[_ FHexibHe a rmored came from appHianceshouHd
be connected directly to junction box.
[_ Fuse both sides of the Mine.
[_ A U.hoHistedconduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connecqons must conform with the
rating of the appHiance and to the requirements of
the NationaH EHectricaH Code, ANSH/NFPA70 -- Hatest
edition (*, See Page 1) and a[[ local codes and
ordinances.
If the house has aluminum wiring, foHHow the
procedure bellow.
a.) Connect the aHuminum wiring to the copper
wire using specia[ connectors designed and
Underwriters Laboratories-Misted for joining
copper to aHuminum. FoHHow the eHectrica[
connector manufacturer's recommended
procedure.
b.) AHuminum/copper connection must conform
with Mccall codes and industry-accepted wiring
practice.
Grasp
over
frame to lift
OVeR
Use screws to attach
oven to cabinet
Reattach side
trim pieces
Remove side
trim
power
supply cable
Remov}X
shipping
feet
Remove trim
SCreWS
Remove
oven door
Preparation
Excessive
Weight Hazard
Use two or more people to move and
install oven.
Failure to follow this instruction
can
result in back or other injury.
IMPORTANT: Use both hands to remove oven
doors.
Do not use handHeor any portion of the front
Before moving oven across floor, check that oven
is on shipping base or sHide oven onto cardboard
or hardboard.
Do not remove shipping feet at the front Mower
corners of oven.
latch on the hinge
in locked position
-
door free to open
and close
latch on the hinge
position
- door
ready for rernoval
Remove trim screw
Pull trim out
Pull top of trim
down
• )
off. Move oven choseto
finaH position.
Remove and discard
shipping materiaHs,tape
and protective fiHmfrom
Do not
the oven. Do not
re
remove shipping base
shipping
feel
or shipping feet at the front Mowercorners of
oven. The shipping feet wiHH protect the Mower
oven trim untiHoven is inserted into cabinet.
Remove and set aside racks and other parts
from inside oven.
m CompHeteHy open oven door. In both back
corners of the door you wiHH see door Hatchesin the
Hockedposition. Rotate both Hatchesforward to the
unHockedposition.
Grasp outside edges of door with both hands.
• Begin dosing door, atthe moment the door
stops dosing, Hiltand puHH door toward you.
. Set door aside on a protective surface.
3B
Remove trim screws attaching right and
Heftside trim to oven. Grasp the bottom end of
trim and puHH away from oven. SHidetop end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2