KitchenAid KEBS207E Instrukcja instalacji - Strona 15
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Piekarnik KitchenAid KEBS207E. KitchenAid KEBS207E 16 stron. 27" (68.6 cm) and 30" (76.2 cm) electric single and double built-in oven
Drukuj stronę
5. The bottom vent and bottom vent trim (required when the
oven is installed with the feet in the tall position) are shipped
in the foam packing at the top of the oven.
To install only the bottom vent, see the following instructions.
To install both the bottom vent and the bottom vent trim for
installations with the feet in the tall position, see the
instructions in Step 6.
Align vent tab (B) with oven frame (A) as shown.
■
Using one #8-18 x ³⁄₈" screw (D) on each side of the vent
■
tab (B), fasten the vent securely to the oven.
D
A. Oven frame
B. Vent tab
6. On models with the feet installed in the tall position, the
bottom vent trim must also be installed. See the following
instructions to install.
Flex the upper vent piece (C) away from the lower vent
■
piece (D) to slide the bottom vent trim (B) between them.
Some force may be required to flex the upper vent trim (C)
away from the lower vent trim (D). Some force may also
be required to flex the bottom vent trim (B) and slide it
into position. Make sure screw holes are properly aligned
between the two pieces. See the following illustration.
Install the bottom vent trim (B) to the lower vent piece (D)
■
using two #8-18 x
" screws on each side.
¹⁄₄
NOTE: On 27" (68.6 cm) models, only one #8-18 x
used on each side.
A
A. #8-18 x
¹⁄₄
" screw
B. Bottom vent trim
A
B
C
C. Oven vent
³⁄₈
D. #8-18 x
" screws
" screw is
¹⁄₄
B
B
D
C
D
C. Upper vent piece
D. Lower vent piece
Align vent tab (B) with oven frame (A) as shown.
■
Using one #8-18 x ³⁄₈" screw (E) on each side of the vent
■
tab (B), fasten the vent securely to the oven.
E
A. Oven frame
B. Vent tab
C. Oven vent
7. Replace the oven racks.
8. Replace the oven door. See the "Replace Oven Door(s)"
section.
9. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
"Prepare Built-In Oven" section.
10. Repeat for lower oven door.
11. Reconnect power.
12. The display panel will light briefly, and "PF" should appear in
the display.
13. If the display panel does not light, reference the "Warranty"
section of the Use and Care Guide.
Install Warming Drawer Deflector Kit (Only
for Ovens Installed Above Warming
On single and double oven models installed above a warming
drawer, a warming drawer deflector kit must be installed. See the
"Tools and Parts" section for information on ordering.
Parts Supplied in Deflector Kit
C
A. Phillips head screws (4)
B. Warming drawer deflector (1)
D
C
D. Bottom vent trim
³⁄₈
E. #8-18 x
" screw
Drawers)
A
only 2 screws for 27" (68.6 cm) size
A
B
B
15