KitchenAid KIRD807HSS0 and Instrukcje instalacji oraz instrukcja obsługi i konserwacji - Strona 10
Przeglądaj online lub pobierz pdf Instrukcje instalacji oraz instrukcja obsługi i konserwacji dla Okap wentylacyjny KitchenAid KIRD807HSS0 and. KitchenAid KIRD807HSS0 and 14 stron. 30" and 36" retractable downdraft vent systems
Drukuj stronę
Recommended
standard
fittings
90° elbow =
45° elbow =
5 ft., (1,5 m)
£5 ft_ ( &8 m)
.!support
leg
4m
Attach support
Uegs to side of
downdraft
vent with two screw's in
each Ueg. Do Not tighten
screws.
cabinet floor. AUign top of bgs
with pencil marks on face of
downdraft
vent.Tighten
screws in
Uegs.
,, Attach 10" (25.4 cm) round
vent collar pUate (suppUied wkh
exterior
Mower system) to front of
downdraft
vent using 4 hex washer
nuts.
l m Put on gloves and safety
glasses. Place cardboard
or another
form of protection
on top of a flat
surface where you can easily
assemble the downdraft
vent
system. Remove parts packages,
downdraft
vent and blower
box
from carton. Remove all shipping
materials,
tape and protective
film
from downdraft
vent and blower
box.
2m
Attach the left side and right
side overcounter
support
brackets
to the downdraft.
Use 1 screw
with each bracket.
Excessive
Weight Hazard
Use two or more people to move
and install downdraft vent,
Faiture to do so can result in back
or other injury.
5m
Carefully
insert
downdraft
vent
into
countertop
cutout.Two
people
are recommended
to
support
the weight
of the
downdraft
vent
during
lifting.
Check that
downdraft
vent
is
parallel
to side of cutout
and that
mounting
brackets
rest gently
on
countertop.
Remove the 2 Phillips-head
screws attaching
the wiring
box
cover and remove cover. Remove
either the back or bottom
knockout
and install conduit connector.
Power supply cable needed
between
exterior
blower assemblv
and blower
box is not provided.
9m
Determine
the location where
the exterior
blower
box wiil be
located. Cut opening
in roof or wail
for vent system to exterior
blower.
install exterior
blower according
to
instructions
supplied
with the
blower
kit.
Wail installations
o Use caulking
compound
between
mounting
flange and wall.
Roof Installations
o Follow standard
roofing
procedures.
o The flashing
sheet should be
entered
over the roof opening.
o Lower edge of flashing
should lie
on top shingles
and upper edge
underneath
shingles.
o Seal assembly
between
roof, fan
and flashing
with roofing
mastic
to prevent leaks.
\
3m
Attach the left side and right
side end caps to the dow'ndraft.
Use 1 screw with each end cap.
10
6m
Move
support
legs down
against
cabinet
floor.
Place a level
against
front
of downdraft
vent
base and adjust
position
of legs
until
downdraft
is level vertically.
Use a pencil
to mark the top of
each leg on face of downdraft
vent.
Then
mark
location
of support
leg
mounting
holes
on cabinet
floor.
Remove
downdraft
vent from
cutout.
Drill starter
holes
at each
mounting
screw'
location
on