KitchenAid 30” Electric Built-in Combination Instrukcje instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Kuchenka mikrofalowa KitchenAid 30” Electric Built-in Combination. KitchenAid 30” Electric Built-in Combination 5 stron.

Drukuj stronę

KitchenAid 30” Electric Built-in Combination Instrukcje instalacji

Electrical

requirements

Electrical Shock Hazard

Electrical ground is required on this

appliance.

Do Not ground to a gas pipe.

Do Not have a fuse in the neutral or

grounding circuit. A fuse in the neutral or

grounding circuit could result in an

electrical shock.

Check with a qualified electrician if you

are in doubt as to whether the appliance is

properly grounded.

Do Not connect to the electrical supply

until appliance is permanently

grounded.

Disconnect power to the junction box

before making the electrical

connection.

Failure to follow these instructions

could

result in serious injury or death.

This appliance must be connected to a

grounded, metallic, permanent wiring

system, or a grounding connector

should be connected to the grounding

terminal or wire lead on the appliance.

Failure to do so could result in a fire,

personal injury or electrical shock.

If codes permit and a separate grounding wire

is used, it is recommended that a qualified

electrician determine that the grounding path

is adequate.

Save Installation

Instructions

for the local

This appliance must be connected to the

proper electrical voltage and frequency

as specified on the serial/rating

plate. Models

rated at

15.0 kw

on 240 volts (11.25 kw on

208 volts) or more require a separate 50-ampere

circuit. Models rated at less than 15.0 kw on 240

volts (11.25 kw on 208 volts) or less require a

separate 40-ampere circuit. Fuse both sides of

the line. A time-delay fuse or circuit breaker is

recommended.

Locate the junction box to allow as

much slack in the cable as possible

Electrical

connection

OVEN MUST BE CONNECTED

WITH

SOLID COPPER WIRE ONLY.

Wire sizes and connections

must

conform to the requirements

of the

National Electrical Code, ANSI/NFPA

70 -

latest

edition**, and all local codes and ordinances for

the kilowatt rating of the oven. Wires sizes and

connections

must conform with the rating of the

oven. This rating can be found on the seriavrating

plate located on the front frame behind the

microwave oven door or lower oven door.

Copies of the standards listed may be obtained

from:

**National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected

directly to the fused disconnect

(or

circuit breaker box) through flexible, armored or

non-metallic

sheathed, copper cable (with

grounding wire). The flexible armored cable

extending from the appliance should be

connected directly to the junction box.

between the junction box and the appliance so

that the oven can be moved if servicing is ever

necessary.

Do Not cut the conduit.

A U.L.-listed conduit connector

must

w provided at the junction box.

A wiring diagram is included in the Tech

Sheet. The Tech Sheet is located

behind the oven control panel.

This appliance is manufactured

with white

(neutral) power supply wire and a cabinet-

connected, green grounding wire twisted

together.

Connect the appliance cable to the junction box

through the U.L.-listed conduit connector.

Complete electrical connection according to local

codes and ordinances.

A. Where local codes permit...

Connecting the cabinet-grounding

conductor

to the neutral (white) junction box wire:

cable from

'unction

power supply

ox \

bare or

green wire

U.L.-listed

conduit

Figure I

cable from

connector

oven

Grounded neutral

1. Disconnect the power supply.

2. Remove the terminal block cover.

3. Connect together 3 wires: green and white

appliance cable wires and the neutral (white)

wire in junction box.

4. Connect the two black wires together; then the

two red wires together. See Figure 1.

B. Where local codes Do Not

permit...

Connecting the cabinet-grounding

conductor

to the neutral (white) junction box wire:

junction

box.

cable from

power supply

white

bare or

green

wires

cable from

conduit

Figure 2 Oven

connector

Ungrounded neutral

1. Disconnect power supply.

2. Separate the green and white appliance cable

wires.

3. Connect the white appliance cable wire to the

neutral (white) wire in the junction box.

4. Connect the two black wires together; then the

two red wires together. See Figure 2.

5. Connect the green or bare grounding wire from

the appliance cable to a grounded wire in the

junction box.

C. If connecting

to a four-wire

electrical

system...

Do Not connect the cabinet-grounding

conductor to the neutral (white) junction box

wire.

junction

box.

cable 1 'ram

power

_ _,~ r.,

SUDBIV

green

wires

ite

:k w rires

Figure 3

connector

1. Disconnect the power supply.

2. Separate the green (or bare) and white

appliance cable wires.

3. Connect the white appliance cable wire to the

neutral (white) wire in the junction box.

4. Connect the two black wires together; then the

two red wires together. See Figure 3.

5. Connect the green appliance cable wire to the

green grounding wire in the junction box.

Now start...

With oven in kitchen.

(II

Remove shipping materials, tape, and

protective film from microwave oven and

oven.

Do Not remove shipping base at

this time.

Remove and unwrap the racks and other

parts from inside the oven. Remove the

air grille'taped to top or side of oven.

Use both hands to remove oven door.

. Grasp only the sides of oven door.

Do Not use handle or any portion of the

front frame or trim for lifting.

Because of the weight and size of the

oven, two or more people are needed to

lift, move and safely install the oven.

Failure to properly grasp the oven door or

to lift oven properly could result in damage

to the product or personal injury.

1 Personal Injury/Property

Damage Hazard

Insert a nail (or equivalent,

5/32" diameter item)

into the hole in each of the hinges. Close the

oven door as far as possible. Lift the oven door

off of the hinges. Set aside.

Property Damage

Before moving oven across floor, check

that oven is on shipping base or slide

oven onto cardboard or hardboard.

Failure to follow these instructions

may

result in damage to floor covering.

Turn power supply off. Move oven close

to final position. Remove and discard

shipping base or cardboard or hardboard. Feed

appliance cable through the opening in cabinet.

Make electrical connection.

See "Electrical

requirements"

and "Electrical connection"

sections, Panel B.

Panel B