Gardena 14770 Instrukcja obsługi - Strona 8

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Sprzęt do trawników i ogrodów Gardena 14770. Gardena 14770 12 stron. Battery pole pruner

Drukuj stronę

2. Slide the protective cover onto the bar and close it until the snap fit

engages.

(A)

3. Push the locking button

and remove the battery

(D)

holder

4. MAINTENANCE

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the chain to stop, remove the battery and slide the

protective cover over the bar before you maintain the product.

To clean the Pole Pruner:

DANGER! Risk of injury!

Risk of injury and risk of damage to the product.

v Do not clean the product with water or with a water jet

(in particular high-pressure water jet).

v Do not clean with chemicals including petrol or solvents.

Some can destroy critical plastic parts.

The airflow slots must always be clean.

1. Clean the pole pruner with a damp cloth.

2. Clean the airflow slots with a soft brush (do not use a screwdriver).

3. Clean the bar with a brush, if necessary.

To clean the battery and the battery charger:

Make sure that the surface and the contacts of the battery and the

battery charger always are clean and dry before you connect the battery

charger.

Do not use running water.

v Battery charger: Clean the contacts and the plastic parts with a soft

and dry cloth.

v Battery: Occasionally clean the ventilation slots and the terminals on

the battery using a soft brush that is clean and dry.

To tension the chain [ Fig. M1 /M2 / M3 /M4 ]:

RISK OF BURN INJURIES!

A too tightly tensioned chain can lead to motor overload and damage,

whereas insufficient tensioning can cause the chain to jump off the rail.

A correctly tensioned chain offers the best cutting performance, opti-

mum battery life and a longer service life. Therefore, you should check

the tensioning regularly as the chain may expand when being used

(especially when the chain is new; following first installation, the tension-

ing of the chain must be checked after the chainsaw has been used for

a few minutes).

v However, do not tension the chain immediately after use but

wait until it has cooled down.

The Allen key for the screws

(17)

is situated inside the protective cover

1. Loosen the two screws

(17)

(Do not unscrew the screws

2. Lift the chain

(19)

in the middle of the bar

The gap should be approx. 2 – 3 mm.

3. Turn the adjusting screw

(24)

clockwise if the chain tension is too low.

(24)

Turn the adjusting screw

counterclockwise if the chain tension is

too high.

4. Retighten the two screws

(17)

5. Start the pole pruner for approx. 10 sec.

6. Check the chain tension again and adjust it if necessary.

5. STORAGE

To put into storage [ Fig. O12 ]:

The product must be stored away from children.

1. Slide the protective cover onto the bar and close it until the snap fit

engages.

2. Remove the battery.

3. Charge the battery.

4. Clean the pole pruner, the battery and the battery charger

(see 4. MAINTENANCE).

(13)

(B)

from the battery

(18)

(17)

(20)

(13)

5. Store the pole pruner, the battery and the battery charger in a dry,

enclosed and frost-free place.

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal household

waste. It must be disposed of in line with local environmental

regulations.

IMPORTANT!

v Dispose of the product through or via your municipal recycling

collection centre.

Disposal of the battery:

The GARDENA battery contains lithium-ion cells that should not

be disposed of with normal household waste at the end of its life.

Li-ion

IMPORTANT!

v Dispose of the batteries through or via your municipal recycling

collection centre.

1. Discharge the lithium-ion cells completely (contact the GARDENA

Service).

2. Protect the contacts on the lithium-ion cells against short circuits.

3. Dispose of the lithium-ion cells properly.

6. TROUBLESHOOTING

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the chain to stop, remove the battery and slide

the protective cover over the bar before you troubleshoot

the product.

To replace the chain [ Fig. M1 /M2 / M3 /T1 ]:

DANGER! Risk of injury!

Cut injury due to the chain.

v Wear protective gloves when replacing the chain.

When the cutting performance reduces significantly (dull chain), the chain

must be replaced. The Allen key for the screws

protective cover

(18)

Only the original GARDENA Spare Chain and Bar Art. 4048 or the

GARDENA Spare Chain Art. 4049 may be used.

(17)

1. Unscrew the two screws

2. Remove the cover

(21)

3. Remove the bar

(20)

with the chain

4. Remove the chain

(19)

from the bar

5. Clean the motor unit

(1)

, the bar

attention to the rubber seals in the housing and the cover

6. Pull the new chain

(19)

over the front stop

Make sure that the chain is running in the right direction and

that the front stop

(a)

points upwards.

(20)

7. Put the bar

on the motor unit

the bar

(20)

and the chain

(19)

is placed around the drive sprocket

8. Put the cover

(21)

on the motor unit

seal.

9. Tighten the two screws

(17)

slightly.

10. Tighten the chain (see 4. MAINTENANCE).

Problem

Possible Cause

Low runtime

Chain is tensioned too much.

Chain is not lubricated due

to lack of oil.

Pole pruner can no longer

Start lever is stuck.

be stopped

Cutting pattern is not clean

Chain is blunt or damaged.

Chain is jammed.

Chain is not tensioned enough. v Tension the chain.

Pole pruner vibrates

Chain is not tensioned enough. v Tension the chain.

severely

(17)

is situated inside the

(19)

(20)

and the cover

(21)

. Pay extra

(21)

(a)

of the bar

(20)

(1)

(22)

so that the pin

is guided through

(23)

(1)

again. Pay attention to the rubber

Remedy

v Tension the chain

(see To tension the chain ).

v Fill in chain oil.

v Remove the battery and

loosen the start lever.

v Replace the chain.