KitchenAid KHHC2090SBL2 Instrukcja instalacji - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Kuchenka mikrofalowa KitchenAid KHHC2090SBL2. KitchenAid KHHC2090SBL2 12 stron. Microwave hood combination

Drukuj stronę

The microwave

oven must be installed on a minimum

of 1 wall

stud, preferably 2, using a minimum

of 1 lag screw, preferably 2.

Using measuring

tape, find and clearly mark the vertical

centerline

of the opening.

.....................

;....................................

A. Centerline

2. With the support tabs facing forward (see illustrations in

"Possible Wall Stud Configurations"

in "Locate Wall Stud(s)"

section), align the mounting plate center markers to the

centerline on the wall, making sure it is level, and that the top

of the mounting plate is butted up against the bottom edge of

the upper cabinet.

NOTE: If the front edge of the upper cabinet is lower than the

back edge, lower the mounting plate so that its top is level with

the front edge of the cabinet.

.............................

...............................

A. Rear wall

B. Mounting plate

C. Top of mounting plate must align

with front edge of cabinet.

D. Front edge of upper cabinet

Holding the mounting plate in place, mark both bottom corner

holes.

Find the wall stud centerline(s) marked in Step 2 of "Locate

Wall Stud(s)," and mark at least 1, preferably 2, hole(s) through

the mounting plate, closest to the wall stud centerline(s). See

figures 1,2 and/or 3 in "Possible Wall Stud Configurations"

"Locate Wall Stud(s)" section. The blackened holes in the

shaded areas are ideal hole locations.

5. Set the mounting plate aside.

Wall Venting Installation Only

Upper cabinet bottom

4" (10.2 era)

d¢

CenterJine

6" (15.2 cm)

6. Mark the centerline 3/8" (1 cm) down from the bottom edge of

the upper cabinet.

10.

11.

12.

Using measuring tape, measure out 6" (15.2 cm) on both sides

of the centerline, and mark.

Measure down 4" (10.2 cm) from the mark made in Step 6,

and mark.

Using a straightedge, draw the 2 horizontal, level lines through

the marks made in steps 6 and 8.

Draw the 2 vertical, plumb lines down from the marks made in

Step 7 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.

This is the venting cutout area.

Cut a 3/4" (19 mm) hole in one corner of the cutout area.

Using a keyhole saw, cut out the venting cutout area.

L_;;S<i}@8_ " sj%,

In addition to being installed on at least 1 wall stud, the mounting

plate must attach to the wall at both bottom corner holes. If the

holes are not over wall studs, use two 1/4-20 x 3" round-head

bolts with toggle nuts; if 1 hole is over a wall stud, use 1 lag screw

and one 1/4-20 x 3" round-head bolt with toggle nut; or if both

holes are over wall studs, use 2 lag screws. Following are

3 installation configurations.

Installation for No Wall Studs at Corner Holes

(Figures I & 2)

Drill 3/4" (19 mm) holes through the wall at both bottom corner

holes marked in Step 3 of "Mark Rear Wall."

Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s)

marked in Step 4 of "Mark Rear Wall." Refer to figures 1 and 2

in "Possible Wall Stud Configurations"

in "Locate Wall Stud(s)"

section.

Installation for Wall Stud at One Corner Hole (Figure 3)

1. Drill a 3/16" (5 mm) hole into the wall stud at the corner hole

marked in Step 3 of "Mark Rear Wall."

2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into

the wall stud at the other hole marked in Step 4 of "Mark Rear

Wall." Refer to Figure 3 in "Possible Wall Stud Configurations"

in "Locate Wall Stud(s)" section.

3. Drill a 3/4" (19 mm) hole through the wall at the other corner

hole.

Installation for Wall Studs at Both Corner Holes

(Figure 4)

1. Drill 3/16" (5 mm) holes into the studs at the corner holes

marked in Step 3 of "Mark Rear Wall."

NOTF: Secure the mounting plate to the wall at both bottom

corner holes drilled into the wall studs and/or drywall using either

1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag

screws.

Refer to illustrations in "Possible Wall Stud Configurations"

"Locate Wall Stud(s)" section.

No Wall Studs at Corner Holes (Figures I & 2)

NOTE: The mounting plate must be secured to the wall on at least

1 wall stud as well as at both bottom corners.

1. With the support tabs of the mounting plate facing forward,

insert 1/4-20 x 3" round-head bolts through both bottom

corner holes of mounting plate.