HIKVISION 143135 Instalacja

Przeglądaj online lub pobierz pdf Instalacja dla System interkomu HIKVISION 143135. HIKVISION 143135 2 stron. Video intercom two-wire kit

Drukuj stronę

DS-KIS702Y(-P)

Video Intercom Two-Wire Kit

UD29996B

KD8003Y-IME2

Two-Wire Module Door Station

Diagram References

Appearance

Microphone

Low Illumination IR Supplement Light

Built-in Camera

Loudspeaker

Call Button

Nametag

TAMPER

Two-Wire Interface

Module-connecting Interface

Terminals

Note: The module-connecting interface is used to connect other function module, such as nametag module, keypad

module, card reader module, etc. All these modules are known as sub module.

Terminal

AIN2: For the access of Door Contact 2

NC1: Door Lock Relay Output (NC)

AIN1: For the access of Door Contact 1

NO1: Door Lock Relay Output (NO)

AIN3: For the access of Exit Button 1

COM: Common Interface

NC2: Door Lock Relay Output (NC)

AIN4: For the access of Exit Button 2

NO2: Door Lock Relay Output (NO)

485-: Module-connecting Interface

GND: Grounding

485+: Module-connecting Interface

12 VDC: Power Output

12V OUT: Module-connecting Interface

GND: Grounding

GND: Module-connecting Interface

Two-Wire Interface

Installation

Note: Video intercom module door sta�on support one-module installa�on, two-module installa�on, three-

module installa�on and more-than-three-module installa�on. Here takes three-module installa�on as an example.

Before you begin:

1. Tools that you need to prepare for installation: Drill (6), cross screw driver (PH1*150 mm), and gradienter.

2. Make sure all the related equipment is power-off during the installation.

3. Make sure you have configured the sub module address before installation. Valid sub module address range is

1 to 8. The No. should be unique for sub modules that connected to the same main unit. The sub module

address and corresponding switch status is shown as the figure.

Sub Module

Address

DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8

Module 1

OFF

Module 2

OFF

Module 3

OFF

Module 4

OFF

Module 5

OFF

Module 6

OFF

Module 7

OFF

Module 8

OFF

Three-Module Flush Mounting

1. Cave the installation hole, and pull the cable out.

Note: The suggested dimension of the installation hole is 321.8(W) × 108(H) × 45.5(D) mm. The suggested length of the

cables left outside is 270 mm.

2. Select a cable entry and remove the plastic sheet. Route the cables through the gang box hole. Insert the

gang box into the installation hole. Mark the gang box screw holes' position with a marker, and take out the

gang box.

3. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into the screw holes.

Fix the gang box with 4 expansion bolts.Fill the gap between the gang box and wall with concrete or Silicone

sealant. Remove the mounting ears

with tool after concrete is dry.

4. Connect cables and insert the modules.

a.Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main unit, then insert the

main unit into the upper grid.

b.Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect one end of Sub Module

1 and insert it into the middle grid.

c.Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it into the bottom grid.

5. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon wrench.

Three- Module Surface Moun�ng

1. Paste the installa�on s�cker 1 onto the wall. Make sure the s�cker is placed

horizontally via measuring with the gradienter. Drill 4 holes according to the screw holes

on the s�cker.

Note: The suggested size of hole is 6(diameter) × 25(depth) mm. The suggested length of the cables le�

outside is 270 mm.

2. Remove the s�cker and insert the expansion sleeves into the screw holes. Fix the

moun�ng frame onto the wall with 4 expansion bolts.

3. Thread the module-connec�ng line across the thread holes of the frame. Pass the

main unit connec�ng line across the thread hole to the top grid and connect the cables.

a.Connect the lines and module-connec�ng line 1 to the corresponding interfaces of

the main unit, then place the main unit into the upper grid.

b.Connect the other end of the module-connec�ng line 1 to the input interface of the

sub modules via module-connec�ng line 2.

c.Organize the cables with cable �e in the package.

4. Insert the modules into the frame a�er wiring. The main unit must be placed in the

top grid.

5. Use the hexagon wrench in the package to fix the cover onto the frame.

Installation Positions

Recommended Installation Height (The distance between the camera and the ground): 1.4 m to 1.6 m

The FOV of the camera is :

Horizontal:

146°,

Vertical: 82°.

The highest visual height and lowest visual height of the camera is shown as picture.

Note:

The power source should be qualified and meet limited power

source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard.

Gang Box

Expansion Bolt

Module-Connec�ng

Line1

Module-Connec�ng

Line2

Main Unit

Sub Module 1

Sub Module 2

Moun�ng Ear

Moun�ng Frame

Main Unit

Hexagonal

Screw

Thread Hole

Cables

Connected

to Main

Unit

Sub Module

Scan the QR code to get User Manual for details.

Hexagonal

Screw

Cover

Hexagon Wrench

Recommended Installation Height (The distance

between the camera and the ground): 1.4 m to 1.6 m

1.4 m

1.5 m