Garmin Avtex TOURER TWO Instrukcja obsługi - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System nawigacji samochodowej Garmin Avtex TOURER TWO. Garmin Avtex TOURER TWO 30 stron.
Getting Started
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
• Update the maps and software on your device
Software Updates, page
• Mount the device in your vehicle and connect it to power
(Mounting and Powering the Garmin Device in Your Vehicle,
page
1).
• Acquire GPS signals
(Acquiring GPS Signals, page
• Adjust the volume
(Adjusting the Volume, page
display brightness
(Adjusting the Screen Brightness,
page
2).
• Set up a vehicle profile for your camper
Profile, page
2).
• Navigate to your destination
Garmin
Device Overview
®
Power key
USB power and data port
Map and data memory card slot
Microphone for Voice Command or hands-free calling
Mounting and Powering the Garmin Device
in Your Vehicle
This product contains a lithium-ion battery. To prevent the
possibility of personal injury or product damage caused by
battery exposure to extreme heat, store the device out of direct
sunlight.
Before you use your device on battery power, you should charge
it.
1
Plug the vehicle power cable
device.
2
Press the mount
onto the suction cup
place.
3
Press the suction cup to the windshield, and flip the lever
back toward the windshield.
4
Fit the tab on the top of the mount into the slot on the back of
the device.
Getting Started
WARNING
(Map and
19).
2) and
(Adding a Vehicle
(Starting a Route, page
WARNING
into the USB port on the
until it snaps into
5
Press the bottom of the mount into the device until it clicks.
6
Plug the other end of the vehicle power cable into a power
outlet in your vehicle.
Turning the Device On or Off
• To turn the device on, press the power key
device to power.
1).
• To put the device in power saving mode, press the power key
8).
while the device is on.
While in power saving mode, the screen is off and the device
uses very little power, but it can wake instantly for use.
TIP: You can charge your device faster by putting it in power
saving mode while charging the battery.
• To turn off the device completely, hold the power key until a
prompt appears on the screen, and select Off.
The prompt appears after five seconds. If you release the
power key before the prompt appears, the device enters
power saving mode.
Acquiring GPS Signals
When you turn on your navigation device, the GPS receiver
must collect satellite data and establish the current location. The
time required to acquire satellite signals varies based on several
factors, including how far you are from the location where you
last used your navigation device, whether you have a clear view
of the sky, and how long it has been since you last used your
navigation device. The first time you turn on your navigation
device, it may take several minutes to acquire satellite signals.
1
Turn on the device.
2
Wait while the device locates satellites.
3
If necessary, go to an open area, away from tall buildings and
trees.
in the status bar indicates the satellite signal strength. When
at least half the bars are filled, the device is ready for navigation.
Status Bar Icons
The status bar is located at the top of the main menu. The status
bar icons display information about features on the device. You
can select some icons to change settings or view additional
information.
GPS signal status. Hold to view GPS accuracy and acquired
satellite information
Bluetooth
settings
Wi-fi signal strength. Select to change the wi-fi settings
(Wireless Network Settings, page
Connected to hands-free calling. Select to place a phone call
(Hands-Free Calling, page
Active vehicle profile. Select to view the vehicle profile settings
(Editing a Vehicle Profile, page
Current time. Select to set the time
page
19).
Battery charge level.
(Viewing GPS Signal Status, page
technology status. Select to view the Bluetooth
®
(Wireless Network Settings, page
18).
14).
2).
(Setting the Time,
, or connect the
22).
18).
1