Alka Natural Water Alka-Pi Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Systemy filtracji wody Alka Natural Water Alka-Pi. Alka Natural Water Alka-Pi 8 stron.

Drukuj stronę

1. Tubing Connections

Operating Parameters:

Water supply:

Feed water temperature:

Safe operating pressure:

Recommended Turbidity:

Recommended pH Range:

Recommended Max. Hardness:

Total Dissolved Solids (TDS):

Tank Air Pressure:

Common System Stages

Stage 1 (FS 1 05)

Stage 2 (FCGACIOK)

Stage 3 (FCGACIOK)

Stage 4 (MTFC50)

Stage 5 (FINCIOI4S)

Introduction

Potable water

33° F - 113° F

40-80 PSI

<5NTU

4-11

7 GPG (120 PPM)

2000 PPM

8-11 PSI (empty)

Sediment filter 5 micron

"Iarning:

•

Open the spigot to flush water from first tank.

•

After installation check the unit for leaks.

•

Do not connect to hot water supply.

•

Change filters regularly

•

Do not freeze unit

•

Heed source water operating parameters

•

Do not use with microbiologically unsafe water

•

Do not use with water of unknown quality

*stages and filters will vary by model and series

Granular Activated Carbon (GAC) filter

Reverse Osmosis membrane (TFC)

In-line carbon polishing filter

Change: 6 months - 1 year

Change: 6 months - I year

Change: 6 months - 1 year

Change: 3 years - 4 years

Change: 6 months - 1 year

Our reverse osmosis drinking water systems have been designed for quick and simple instaJlation and maintenance. By

carefully reading this instruction manual and following the operational guidelines you will insure a successful installation and

reliable operation. Routine maintenance is essential to the longevity and performance of the system. Filters should be changed

regularly, depending on the quality of the feed water supply and quantity of water used.

Liability:

The installer is responsible for any leaks resulting from installation of tubing or related fittings. The installer must check over

the entire unit completely while under pressure to ensure unit is not leaking and functioning properly. Liability resulting from

failure to check for leaks while under pressure is the sole responsibility of the installer. Maximum pressure rating is 85 PSI. If

local water pressure exceeds 75 PSI, a pressure regulator must be installed, reducing the water pressure into the system.

Starting Your Installation

Component Checklist:

1 - Storage Tank

1 - RO System

I - Faucet (with faucet install kit)

1 - Installation Kit

Avoid installation locations where the system might come in contact with

hot water pipes or other hazards. Determine the location for the faucet.

Check to see that drilling the faucet hole will not damage pipes or wires

underneath the sink. Determine the location for the storage tan1e A

maximum distance of 15 feet from tank to faucet is possible. A shorter

tubing run from tank to faucet will produce a faster flow out of the faucet.

Tubing and Fittings

To insure an optimal seal, tubing should be cut with the end square. An angled cut or distortion or kink of the tubing will not

provide an efficient seal and may cause leaks.

Your system may come with quick-connect or standard compression fittings. With quick-connect style fittings, simply push

the tube into the collet ring until you feel the tubing click into place. To remove, hold the collet ring flush against the fitting

while pulling the tube out in the opposite direction. Standard compression fittings will usually have a nut, ferrule and insert.

First slide the nut over the tubing end followed by the ferrule, then slide the insert inside the tubing end. Push the tubing into

the fitting as far as possible then tighten down the nut on the threads.