Garmin GPSMAP 751xs Instrukcja obsługi - Strona 23

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Morski system GPS Garmin GPSMAP 751xs. Garmin GPSMAP 751xs 38 stron.
Również dla Garmin GPSMAP 751xs: Skrócona instrukcja obsługi (4 strony), Instrukcja instalacji (8 strony)

Drukuj stronę

may differ from the automatic gain setting used for another

mode.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain > Auto.

The chartplotter sets the gain automatically once, based on

average conditions, the range of the radar signal, and the

selected radar mode. The chartplotter does not readjust the

gain automatically in response to changing conditions.

Manually Adjusting Gain on the Radar Screen

For optimal radar performance that accounts for actual

conditions, you can manually adjust the gain.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Select Up to raise the gain, until light speckles appear across

the Radar screen.

Data on the Radar screen is refreshed every few seconds.

As a result, the effects of manually adjusting the gain may

not appear instantly. Adjust the gain slowly.

Select Down to lower the gain until the speckles disappear.

If boats, land, or other targets are within range, select Down

to lower the gain until the targets begin to blink.

Select Up to raise the gain until the boats, land, or other

targets appear steadily lit on the Radar screen.

Minimize the appearance of nearby large objects, if

necessary.

Minimize the appearance of side-lobe echoes, if necessary.

Minimizing Nearby Large-Object Interference

Nearby targets of significant size, such as jetty walls, can cause

a very bright image of the target to appear on the Radar screen.

This image can obscure smaller targets located near it.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Select Down to lower the gain until the smaller targets are

clearly visible on the Radar screen.

Reducing the gain to eliminate nearby large-object

interference may cause smaller or distant targets to blink or

disappear from the Radar screen.

Minimizing Side-Lobe Interference on the Radar Screen

Side-lobe interference may appear to streak outward from a

target in a semi-circular pattern. Side-lobe effects can be

avoided by reducing the gain or reducing the radar range.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Select Down to lower the gain until the semi-circular,

streaked pattern disappears from the Radar screen.

Reducing the gain to eliminate side-lobe interference may

cause smaller or distant targets to blink or disappear from

the Radar screen.

Adjusting Sea Clutter on the Radar Screen

You can adjust the appearance of clutter caused by choppy sea

conditions. The sea clutter setting affects the appearance of

Radar

nearby clutter and targets more than it affects the appearance

of distant clutter and targets. A higher sea clutter setting

reduces the appearance of clutter caused by nearby waves, but

it can also reduce or eliminate the appearance of nearby

targets.

NOTE: Depending upon the radar in use, the sea clutter setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Sea Clutter > Presets.

Select a setting that reflects the present sea conditions.

Select Menu > Noise Rejection > Sea Clutter.

Select Up or Down to adjust the appearance of sea clutter

until other targets are clearly visible on the Radar screen.

Clutter caused by sea conditions may still be visible.

Adjusting Rain Clutter on the Radar Screen

You can adjust the appearance of clutter caused by rain.

Reducing the radar range also can minimize rain clutter

(page

15).

The rain clutter setting effects the appearance of nearby rain

clutter and targets more than it effects the appearance of distant

rain clutter and targets. A higher rain clutter setting reduces the

appearance of clutter caused by nearby rain, but it can also

reduce or eliminate the appearance of nearby targets.

NOTE: Depending upon the radar in use, the rain clutter

settings configured for use in one radar mode may or may not

be applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Rain Clutter.

Select Up or Down to decrease or increase the appearance

of nearby rain clutter until other targets are clearly visible on

the Radar screen.

Clutter caused by rain may still be visible.

Reducing Cross Talk Clutter on the Radar Screen

You can reduce the appearance of clutter caused by

interference from another nearby radar source, when the Cross

Talk Reject setting is on.

NOTE: Depending upon the radar in use, the crosstalk setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Cross Talk Reject.

Radar Display Settings

From any Radar screen or the Radar overlay, select Menu >

Radar Setup.

Orientation: Sets the perspective of the radar display. The

orientation setting applies to every radar mode. This setting

does not apply to the Radar overlay.

Appearance: Sets the color scheme, look-ahead speed, and

navigation appearance.

Front of Boat: Compensates for the physical location of the

radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Radar Appearance Settings

From a Radar screen, select Menu > Radar Setup >

Appearance.

NOTE: These settings do not apply to the Radar overlay.

Color Scheme: Sets the color scheme.

Look-Ahead Speed: Shifts your present location toward the

bottom of the screen automatically as your speed increases.

Enter your top speed for the best results.

Heading Line: Shows an extension from the bow of the boat in

the direction of travel on the radar screen.